Xerox FaxCentre F12 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 380

background image

Introduction

1-8

3/03

WorkCentre Pro 412, FaxCentre F12 &

WorkCentre M15/M15i

General safety warning
Switch off the power to the machine and disconnect the power cord from the outlet while performing tasks
that do not need the electricity on. Contact with electricity can cause death or injury.

Power Supply
This product must be operated from the type of power supply indicated on the product’s data plate label.
This product must be connected to a protective earth circuit.

Safe Working
Throughout this procedure prior to working on any electrical circuit or any mechanical drive component dis-
connect all electrical power to the product. The disconnect device is the power cord. Remove the plug from
the power outlet.

Ventilation
This product should not be placed in a built-in installation unless proper ventilation is provided.

Operator Accessible Areas
This product has been designed to restrict operator access to safe areas only. Operator access to hazard-
ous areas is restricted with covers or guards, which require a tool to remove. Ensure that these covers or
guards are correctly replaced after every service or maintenance task.

Maintenance/Service
Do not to carry out any maintenance or service on the product, which is not described this service docu-
mentation.

Cleaning
Before cleaning this product, unplug the product from the power outlet. Always use materials specifically
designated for this product, the use of other materials may result in poor performance and may create a
hazardous situation. Do not use aerosol cleaners, they may become flammable under certain circum-
stances.

AVERTISSEMENT

Cette mention indique des informations relatives à différentes situations de maintenance.

Sécurité générale - Avertissement
Mettre la machine hors tension et débrancher le cordon d'alimentation de la prise murale lors d'interven-
tions qui ne nécessitent pas que l'alimentation soit maintenue. Un contact avec une zone sous tension
peut mettre en danger la sécurité des personnes.

Alimentation
Ce produit doit être utilisé avec l'alimentation indiqué sur la plaque de la machine.
Ce produit doit être connecté à un circuit avec mise à la terre.

Sécurité
Pendant toute cette procédure d'intervention dans des circuits électriques ou des entraînements méca-
niques, débranchez la machine. Le système de déconnexion est le cordon d'alimentation. Retirer le con-
necteur de la prise murale.

Aération
Cet équipement ne doit pas être encastré, sans une ventilation appropriée.

«
...
14
15
16
17
18
...
»

Содержание FaxCentre F12





























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FaxCentre F12

Бренд: Canon Страницы: 149

Бренд: Canon Страницы: 60

Бренд: Lanier Страницы: 4

Бренд: Magicard Страницы: 26

Бренд: QMS Страницы: 194

Бренд: Xerox Страницы: 2

Бренд: Oki Страницы: 1

Бренд: Konica Minolta Страницы: 15

Бренд: SPRT Страницы: 13

Бренд: Oki Страницы: 105

Бренд: Lanier Страницы: 4

Бренд: Dascom Страницы: 2

Бренд: Konica Minolta Страницы: 102

VersaLink C9000

Бренд: Xerox Страницы: 255

Бренд: WOOSIM Страницы: 20

Бренд: MINOLTA-QMS Страницы: 67

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды