manualshive.com logo in svg

Xerox DocuColor 2060, Руководство по обслуживанию, Страница: 64 / 88

Поделиться
Скачать
Xerox DocuColor 2060 Скачать руководство пользователя страница 64

Default settings for the printer engine

7-12

 Guide to Performing Routine Maintenance

Setting the audio tone

There are three types of audio tones that can be activated on the 
printer:

•

Attention tone: This tone indicates that an unselectable 
button has been touched or pressed.

•

Button Selection tone: This tone indicates that a selectable 
button has been touched or pressed.

•

Fault tone: This tone indicates that the printer is in a fault 
condition and cannot continue printing.

Each of these tones can be deactivated or set to Soft, Normal, or 
Loud. The factory default setting is Normal.

To set the audio tone:

1. Access the Tools mode (refer to the section “Accessing the 

Tools mode” in this chapter).

2. On the Machine Default 1 screen, touch the Audio Tones 

button. The Audio Tones screen displays.

Figure 7-13. Audio Tones screen

3. Touch the button for the desired volume setting for each tone.

To deactivate a tone, touch the Off button for that tone.

4. Touch the Reset button to restore the factory default setting 

for the three tones.

5. Touch the Close button to return to the Machine Defaults 1 

screen.

Содержание DocuColor 2060

























































































Отзывы:

Нет отзывов