Xerox 4150 - WorkCentre B/W Laser, Руководство по обслуживанию

Страница: 152 / 631

January 2016
2-79 WorkCentre WorkCentre 4150/4250/4260WorkCentre 4150/4250/42604150/
12-100, 12-200
Status Indicator RAPs
12-100 Finisher Jam 3 RAP
12-100 The finisher entrance sensor failed to actuate within the correct time after the document
was fed from the exit sensor.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
NOTE: The finisher door switch must be closed to 24V to the motors.
Refer to (4250/4260/4265) Wiring Diagram 14 and Wiring Diagram 15 . Perform the following:
1. Open the finisher front door, PL 12.10 Item 1 . Lower the document entry guide PL 12.15
Item 23 . Remove all jammed documents. Open the side cover assembly, PL 7.30 Item 1 ,
remove all jammed paper.
2. Check the document entry guide, PL 12.15 Item 23 for damage.
3. Check that the finisher entry sensor actuator, PL 12.15 Item 20 moves freely and is not
damaged.
4. Enter dC330 code 12-800. Check the finisher entrance sensor (Q12-800), PL 12.15 Item
15 .
5. Check the wiring between the finisher entrance sensor and J7 on the Finisher PWB . If
necessary, install a new finisher entrance sensor, PL 12.15 Item 15 .
6. Enter dC330 code 12-100. Check that the entrance motor (MOT12-100), PL 12.15 Item 5
runs and drives the finisher entry roll, PL 12.15 Item 2 .
7. Check the wiring between the entrance motor and J5 on the Finisher PWB .
8. Check the drive belt, PL 12.15 Item 26 . If necessary, install a new drive belt.
9. Check that the finisher entry roll, PL 12.15 Item 2 and the finisher entry roll idlers, PL
12.15 Item 21 are clean and rotate freely.
10. Check that the finisher PWB DIP switch settings are correct. Refer to the 12A Finisher
PWB DIP Switch Settings RAP.
11. If necessary, install new components:
• Entrance motor, PL 12.15 Item 5 .
• Finisher PWB, PL 12.10 Item 8 .
12-200 Finisher Jam 4 RAP
12-200 The exit sensor failed to actuate within the correct time after the document was fed
from the finisher entrance sensor.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
NOTE: The finisher door switch must be closed to 24V to the motors.
Refer to Wiring Diagram 14 and Wiring Diagram 15 . Perform the following:
1. Open the finisher front door, PL 12.10 Item 1 . Lower the document entry guide PL 12.15
Item 23 . Remove all jammed documents.
2. Check that the exit sensor actuator, PL 12.20 Item 3 moves freely and is not damaged.
NOTE: If necessary, remove the finisher to check the exit sensor actuator. Refer to REP
12.1 .
3. Enter dC330 code 12-805. Check the exit sensor (Q12-805), PL 12.20 Item 7 .
4. Check the wiring between the exit sensor and J7 on the Finisher PWB . If necessary,
install a new exit sensor, PL 12.20 Item 7 .
5. Enter dC330 code 12-100. Check that the entrance motor (MOT12-100), PL 12.15 Item 5
runs and drives the transport roll, PL 12.15 Item 2 .
6. Check the wiring between the entrance motor and J5 on the Finisher PWB .
7. Check the drive belt, PL 12.15 Item 26 . If necessary, install a new drive belt.
8. Check that the transport roll, PL 12.15 Item 2 and transport roll idlers, PL 12.15 Item 21
are clean and rotate freely.
9. Check that the finisher PWB DIP switch settings are correct. Refer to the 12A Finisher
PWB DIP Switch Settings RAP.
10. If necessary, install new components:
• Document entrance motor, PL 12.15 Item 5 .
• Finisher PWB, PL 12.10 Item 8 .