Xerox 1235DT - Phaser Color Solid Ink Printer Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 239

background image

28

Phaser 1235 Network Color Printe

r

U10

Roller Position Error U10 Power Off/On

U10-Roller Position Error

1. Ensure the correct weight and type of paper is loaded in the currently used

tray. Also ensure the paper is loaded correctly in the tray.

2. Clean the pick and registration rollers.
3. Ensure there are no obstructions in the paper path.
4. Test the registration motor and clutch as described in “Motor and clutch

tests” on page 69. Replace the motor or clutch if necessary.

5. Inspect the wiring for the registration clutch and registration motor.
6. Replace the engine controller board.

U12

Duplex I/F Error U12 Power Off/On

U12-Duplex I/F Error

1. Turn the printer off and on.
2. Pull out the duplexer and inspect its connector at the right front corner (the

connector faces rearward). Inspect the printer’s corresponding connector
on the printer chassis (covered by a flexible metal plate).

3. Inspect the wiring harness leading from the engine control board to the

duplex unit connector.

4. Replace the duplex unit.
5. Replace the engine controller board.

U13

Tray 3 I/F Error U13 Power Off/On

U13-Tray 3 I/F Error

U14

Tray 2 I/F Error U14 Power Off/On

U14-Tray 2 I/F Error

1. Turn the printer off and then on.
2. Inspect the interface connector connecting the tray unit to the print engine.

Inspect the printer’s corresponding connector on the underside of the
printer. Inspect the wiring harness leading from the connector to the
engine control board.

3. Replace the engine controller board.

U15

Control Panel Error U15 Power Off/On

U15-Control Panel Error

1. Turn the printer off and then on.
2. Reset the printer NVRAM using the procedure “Resetting NVRAM” on

page 85.

3. Replace the engine controller board.

U18

Yellow LED Error U18 Power Off/On

U18-Yellow LED Bar
Missing

U19

Magenta LED Error U19 Power Off/On

U19-Magenta LED Bar
Missing

U20

Cyan LED Error U20 Power Off/On

U20-Cyan LED Bar Missing

U21

Black LED Error U21 Power Off/On

U21-Black LED Bar Missing

1. Ensure the LED assembly is correctly installed.
2. Inspect the wiring harnesses leading to the LED assembly.
3. Replace the engine controller board.

Printer fault messages

Code

Front panel message

Service message

«
...
39
40
41
42
43
...
»

Содержание 1235DT - Phaser Color Solid Ink Printer
















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1235DT - Phaser Color Solid Ink Printer

M-Class Mark II M-4206

Бренд: Datamax Страницы: 22

Бренд: DataCard Страницы: 7

Бренд: MEFA Страницы: 2

Бренд: Xerox Страницы: 24

Magicolor 4650DN

Бренд: Konica Minolta Страницы: 260

Intelliprint cL160

Бренд: Genicom Страницы: 216

Бренд: Me3D Страницы: 14

Бренд: Mitsubishi Страницы: 2

Бренд: Oki Страницы: 182

Бренд: Citizen Страницы: 44

BIZHUB 8050 CF5001

Бренд: Konica Minolta Страницы: 20

Бренд: Jetmobile Страницы: 56

Бренд: Kyocera Mita Страницы: 14

9500 - HL 1660EN B/W Laser Printer

Бренд: Brother Страницы: 258

1450B002 - PIXMA MP510 All-in-One Photo Printer

Бренд: Canon Страницы: 98

Бренд: Canon Страницы: 4

Бренд: Canon Страницы: 116

Бренд: Canon Страницы: 176

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды