Xerox 1235DT - Phaser Color Solid Ink Printer Скачать руководство пользователя страница 200 | Manualshive

Страница: 200 / 239

background image

Service Guide

187

FRU List

This topic provides a list of field replaceable units for the printer.

Changes to Xerox instruments are made to accommodate improved components
as they become available. It is important when ordering parts to include the
following information:

■

Component's part number.

■

Instrument type or number.

■

Instrument serial number.

■

Modification number, if any.

Using the parts list

■

The numbers shown in each illustration correspond to the parts list

number for that illustration.

■

The capital letters “C”, “E”, and “S” shown in an illustration stand for

C-ring, E-ring, and Screw, respectively.

■

A shaded triangle t in an illustration indicates the item is part of an

assembly.

■

The notation “with X~Y” following an part name indicates an assembly

that is made up of components X through Y. For example, “1

(with 2~4)” means part 1 consists of part 2, part 3, and part 4.

■

An asterisk * following a part name indicates the page contains a note

about this part.

■

The notation “J1<>J2 and P2” is attached to a wire harness. It indicates

that connector jack 1 is attached to one end of the wire harness and

connector jack 2 is attached to the other end that is plugged into plug 2.

■

A notation “(part of item 1.1)” indicates that the part is included with

item 1.2.1 (PL1.2, line item 1).

«
...
198
199
200
201
202
...
»

Содержание 1235DT - Phaser Color Solid Ink Printer
















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1235DT - Phaser Color Solid Ink Printer

Бренд: Oki Страницы: 282

Бренд: MakerPi Страницы: 21

Бренд: Nantian Electronics Страницы: 4

Бренд: JCM Страницы: 22

Бренд: Lanier Страницы: 265

WorkCentre 7800 series

Бренд: Xerox Страницы: 14

WORKCENTRE 7775

Бренд: Xerox Страницы: 15

WORKCENTRE 7775

Бренд: Xerox Страницы: 24

WORKCENTRE 7755

Бренд: Xerox Страницы: 252

WORKCENTRE 7755

Бренд: Xerox Страницы: 15

WORKCENTRE 7755

Бренд: Xerox Страницы: 40

WorkCentre 5019

Бренд: Xerox Страницы: 50

versalink C7020

Бренд: Xerox Страницы: 20

WorkCentre 4265

Бренд: Xerox Страницы: 4

Бренд: Xerox Страницы: 4

Бренд: Xerox Страницы: 281

Бренд: Xerox Страницы: 100

Бренд: Xerox Страницы: 629

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды