Xerox 1235DT - Phaser Color Solid Ink Printer Скачать руководство пользователя | Manualshive

Страница: 2 / 239

background image

Users safety summary

Terms in

CAUTION

Conditions that can result in damage to the product.

manual:

WARNING

Conditions that can result in personal injury
or loss of life.

Power source:

For 110 VAC printers, Do not apply more than 140 volts RMS

between the supply conductors or between either supply conductor and ground.
Use only the specified power cord and connector. For 220 VAC printers, do not
apply more than 260 volts RMS between the supply conductors or between either
supply conductor and ground. Use only the specified power cord and connector.
Refer to a qualified service technician for changes to the cord or connector.

Operation of product:

Avoid electric shock by contacting a qualified service

technician to replace fuses inside the product. Do not operate without the covers
and panels properly installed. Do not operate in an atmosphere of explosive
gases.

Safety instructions:

Read all installation instructions carefully before you plug the

product into a power source.

Terms on

CAUTION

A personal injury hazard exists that may not be

product:

apparent. For example, a panel may cover the hazardous area.
Also applies to a hazard to property including the product itself.

DANGER

A personal injury hazard exists in the area where
you see the sign.

Care of product:

Disconnect the power plug by pulling the plug, not the cord.

Disconnect the power plug if the power cord or plug is frayed or otherwise
damaged, if you spill anything into the case, if product is exposed to any excess
moisture, if product is dropped or damaged, if you suspect that the product needs
servicing or repair, and whenever you clean the product.

Ground the product:

Plug the three-wire power cord (with grounding prong) into

grounded AC outlets only. If necessary, contact a licensed electrician to install a
properly grounded outlet.

«
1
2
3
4
...
»

Содержание 1235DT - Phaser Color Solid Ink Printer
















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1235DT - Phaser Color Solid Ink Printer

Бренд: Xerox Страницы: 25

Бренд: DataCard Страницы: 2

Бренд: Oki Страницы: 36

Бренд: Oki Страницы: 3

Бренд: UltraTape Страницы: 52

Бренд: Ultimaker Страницы: 101

Бренд: Canon Страницы: 18

MultiPASS MPC190

Бренд: Canon Страницы: 8

Бренд: Savin Страницы: 160

Бренд: GCC Technologies Страницы: 2

Бренд: Stratasys Страницы: 68

Бренд: Keithley Страницы: 97

Бренд: TonerRefillKits Страницы: 10

VERSAJET MP3200 Series

Бренд: Cino Страницы: 18

Бренд: Star Micronics Страницы: 127

Бренд: Canon Страницы: 70

Бренд: Star Micronics Страницы: 73

Бренд: Brother Страницы: 144

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды