Xerox 1235DT - Phaser Color Solid Ink Printer Скачать руководство пользователя

Страница: 35 / 239

Phaser 1235 Network Color Printer

A11

Jam A11, Remove Output Open Cover A, See
Labels

A11-Paper Feed Jam

Ensure the correct weight and type of paper is loaded in the currently used
tray. Also ensure the paper is loaded correctly in the tray.

Clean the pick and registration rollers.

Ensure there are no obstructions in the paper path.

Test the registration motor and clutch as described in “Motor and clutch
tests” on page 69. Replace the motor or clutch if necessary.

Inspect the wiring for the registration clutch and registration motor.

Replace the engine controller board.

A22

Jam A22, Remove Output Open Cover A, See
Labels

A22-Feed Path Jam

Ensure the correct weight and type of paper is loaded in the currently used
tray. Also ensure the paper is loaded correctly in the tray.

Clean the pick and registration rollers.

Ensure there are no obstructions in the paper path.

Test the registration motor and clutch as described in “Motor and clutch
tests” on page 69. Replace the motor or clutch if necessary.

Inspect the wiring for the registration clutch and registration motor.

Replace the engine controller board.

Jam B8 Open Cover B, See Labels

B8-Duplex Jam

Ensure the correct weight and type of paper is loaded in the currently used
tray. Also ensure the paper is loaded correctly in the tray.

Clean the duplex unit’s rollers.

Test the duplex motor and clutch as described in “Motor and clutch tests”
on page 69.

Replace the duplex unit.

Replace the engine controller board.

B13

Jam B13 Open Area B, See Labels

B13-Duplex Inverter Jam

Ensure the correct weight and type of paper is loaded in the currently used
tray. Also ensure the paper is loaded correctly in the tray.

Inspect and clean the eject rollers behind the fuser unit.

Ensure the paper path leading to the duplex unit and the duplex unit’s paper
path are both clear of obstructions.

Inspect the operation of the solenoid activated separator gate the direct the
print into the duplex unit. Test the exit solenoid with the “Motor and clutch
tests” on page 69.

Replace the duplex unit.

Replace the engine controller board.

Printer fault messages

Code

Front panel message

Service message

Содержание 1235DT - Phaser Color Solid Ink Printer
















































































































































































































































Результаты поиска

Содержание 1235DT - Phaser Color Solid Ink Printer

Отзывы:

Похожие инструкции для 1235DT - Phaser Color Solid Ink Printer

Бренды по названию

Популярные бренды

Xerox 1235DT - Phaser Color Solid Ink Printer, Руководство по обслуживанию

Результаты поиска

Содержание 1235DT - Phaser Color Solid Ink Printer

Отзывы:

Похожие инструкции для 1235DT - Phaser Color Solid Ink Printer

Бренды по названию

Популярные бренды