manualshive.com logo in svg

Xantrex XW4024 230 50, Руководство по установке, Страница: 35 / 68

Поделиться
Скачать
Xantrex XW4024 230 50 Скачать руководство пользователя страница 35

Step 4: Wiring the Inverter

975-0384-01-02

2–17

This manual for use by qualified personnel only

7.

Connect the other end of the cable to the NEGATIVE (–) terminal on the 
battery.

8.

Use a wrench to tighten the bolt to the required torque.

9.

Attach the DC terminal covers.

Important:

The next step is the last cable connection. A spark is normal when 

this connection is made.

Figure 2-10

Battery Cable Connection

CAUTION: Damage to Equipment

Do not put anything between the battery cable lug and the terminal surface. 
Overheating of the terminal may occur. Do not apply any type of antioxidant 
paste until after the battery cable wiring is tightened. The same applies for all DC 
connections. Do not over-tighten; observe all recommended torque values.

CAUTION: Reverse Polarity Damage

Before making the final DC connection or closing the DC breaker or disconnect, 
check cable polarity at both the battery and the inverter/charger. Positive (+) 
must be connected to positive (+). Negative (–) must be connected to 
negative (–).

Reverse polarity damage is not covered by warranty.

Terminal surface

Copper compression lug

Make sure nothing is between the terminal 
surface and the battery cable lug

Battery cable lug

Flat washer

3/8-15 x 5/8” bolt (supplied)

Shrink-wrap to 
color-code the cable

Split-ring lock washer

Содержание XW4024 230 50





































































Отзывы:

Нет отзывов