Xantrex XW4024 230 50 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 68

Xantrex XW4024 230 50 Скачать руководство пользователя страница 17

System Components and Accessories

975-0384-01-02

1–7

This manual for use by qualified personnel only

Generator

The generator should be a 230V, single-phase generator with automatic starting
capabilities.

Generator
Compatibility

The Xantrex XW Automatic Generator Start supports most two- and three-wire
generator starters. Some manufacturers include, but are not limited to, Onan
(Quiet Diesel, gasoline, and LP), Power Tech, Generac, Northern Lights, Fisher
Panda, Westerbeke, Kohler, Honda, and Yamaha. Check with the generator
manufacturer to make sure your generator has automatic starting capabilities
and is compatible with the Xantrex XW Automatic Generator Start. For more
information, see the Xantrex XW Automatic Generator Start Owner’s Guide.

Xantrex XW
System Control
Panel

A Xantrex XW System Control Panel is required to configure the Xantrex XW
Automatic Generator Start and monitor generator starting and stopping activity.

«
...
15
16
17
18
19
...
»

Содержание XW4024 230 50





































































Отзывы:

Нет отзывов