background image

M A - 5   Q C     S P E C T R O P H O T O M E T E R  

4

 

Russia 

 

 

Korean Battery Application 

Korean battery safety standard KC 62133(2015-07), Application No. XU101195-18004A 

 

Equipment Information 

Use of this equipment in a manner other than that specified by X-Rite, Incorporated may compromise design 

integrity and become unsafe. 

 

To avoid discomfort, do not look directly into the measurement optics when the instrument is on. 

 

No user serviceable parts in this product. 

 

WARNING:

 This instrument is not for use in explosive environments. 

 

Do not immerse the instrument in liquid. 

 

Transportation

: This product contains a lithium-ion battery. Should you need to ship this device, you may wish to 

consult published guidance documents by one or more of these organizations for advice on how to comply with the 

regulations: IATA, ICOA, IMDG & PHMSA. The battery contained in this device is 46g in weight, 3.6V, 2.15 Ah, 

and complies with the UN 38.3 tests in effect the year it was originally shipped

 

The instrument is a sensitive measurement instrument. If the instrument experiences a drop, a calibration should 

be performed followed by a self test before any measurements are taken to ensure the instrument is working 

properly. Refer to the Calibration section for information on performing a Calibration. 

 

Instructions for disposal: Please dispose of Waste Electrical and Electronic Equipment (WEEE) at designated 

collection points for the recycling of such equipment. 

 

 

Firmware Software Licenses 

 

1.  Firmware consists of source code of: 

Copyright 2006, Atmel Corporation 

All rights reserved 

 

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the 

following conditions are met: 

 

 - Redistributions of source code must retain the above copyright notice, this list of conditions and the disclaimer 

below. 

 

 - Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the 

disclaimer below in the documentation and/or other materials provided with the distribution.  

 

Atmel's name may not be used to endorse or promote products derived from this software without specific prior 

written permission.  

  

DISCLAIMER:  THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED 

WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, 

FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE DISCLAIMED. IN NO EVENT 

SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 

CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE 

Содержание MA-5 QC








































Отзывы: