manualshive.com logo in svg

X-Rite 890, Руководство по эксплуатации, Страница: 47 / 52

Поделиться
Скачать
X-Rite 890 Скачать руководство пользователя страница 47

 

 

E-1

 

A P P E N D I X   E 

890 Instrument 

Firmware Update 

The instrument’s firmware is upgraded using Interface Cable P/N SE108-70 and  
DB Adapter P/N 881-71, both available from X-Rite. 

The following items are required to perform a 890 instrument firmware update:  

•

 

Computer with an available serial port 

•

 

890 instrument with AC adapter 

•

 

Update firmware disk 

•

 

Interface cable (P/N SE108-70) and DB25 adapter (P/N 881-71) 

NOTE: Computer screen savers must be disabled during the update 
procedure. Once the update has been started, the old firmware 
version is permanently erased. 

Step 1  Cabling Connection Procedure

 

•

 

Insert one end of the interface cable P/N SE108-70 into the I/O port on the 
instrument. Modular connector only inserts in one direction. 

•

 

Insert the other end of the interface cable into the DB25 Adapter P/N 881-71. 

•

 

Attach the DB25 adapter to an available “RS-232” I/O port on the computer. 

 

890 Instrument

I/O Serial Port 

Interface Cable P/N SE108-70

DB25 Adapter P/N 881-71 

Содержание 890





















































Отзывы:

Нет отзывов