manualshive.com logo in svg

X-Rite 890, Руководство по эксплуатации, Страница: 25 / 52

Поделиться
Скачать
X-Rite 890 Скачать руководство пользователя страница 25

 

S E T T I N G   S Y S T E M   C O N F I G U R A T I O N  

 

3-3 

XON 

When set to On (XON), this enables bi-directional transmit On/Off protocol. 
When set to Off (xon), the instrument ignores XON/OFF codes. Note, usage 
is limited to output at this point. 

Page 2b Configuration Options 

DPT (Decimal Point) 

Controls the decimal point availability during data output. When off (dtp), no 
decimal is output with data. When on (DTP), decimal points are included 
with the output data. 

COMP (Compact) 

Varies the output format of the data. When off (comp), data for each color is 
delimited with a carriage return—or CR LF if ALF is enabled. When on 
(COMP), a space and delimiter is transmitted after each set of  RGB data values. 

ALF (Automatic Line Feed) 

Controls the line feed availability during data output. When off (alf), no line 
feed is output with data. When on (ALF), a line is included with the output 
data. 

Page 2c Configuration Options 

DEL (Delay) 

Controls a transmitted delay between each set if RGB data output. When off 
(del), no delay is sent between each set of RGB data. When on (DEL), a one 
second delay is sent between each set of RGB data. 

AXMT (Automatic Transmit)

 

Controls automatic transmission of data after a measurement. When off 
(axmt), no data is transmitted out the I/O port after a measurement. When on 
(AXMT), data is automatically sent out the I/O after a measurement. 

Page 2d Configuration Options 

BAUD (Rate)

 

Determines the data output rate (characters per second) of the I/O port. 
Available settings are: 110, 300, 600, 1200, 2400, 4800, and 9600. 

LOCK 

Controls the ability to change the configuration options. When off (lock), 
configuration options are available for change. When on (LOCK), 
configuration options cannot be changed. Note, an additional step is required 
to change this option, refer to the following procedure for details. 

Configuration Setup Procedure 

•

 

Options that toggle on and off display in upper-case (on) or lower-case 
(off). For example, COMP = on and comp = off.  

Содержание 890





















































Отзывы:

Нет отзывов