X-Rite 890 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 52

X-Rite 890 Скачать руководство пользователя страница 13

G E T T I N G S T A R T E D

1-5

Display and Keyswitch Definition

The characters in the bottom row of the display dictate which function is
selected or which action takes place when a corresponding keyswitch is
pressed. Normally, upper-case lettering in the top row of the display is used
for messages, and lower-case lettering in the bottom row is used for menu
options that are selectable.

Each keyswitch is embossed with identification marks signifying its number.
The left-most key is labeled “

I

”, center-left key is labeled “

ll

”, and so on.

Keyswitches that are used to select a function or perform an action are tinted
(grayed) throughout this manual.

MAIN MENU

film

p1 pap

bal

Menu Keys

Keyswitch

lll

and

llll

have the word “MENU” printed above them. Pressing

these two keys simultaneously at any location in the menu structure causes
the display to return to page 1 of the main menu.

MAIN MENU

film

p1 pap

bal

MENU

Help Messages

Built-in help messages are available for most functions. Help messages are
activated by pressing and holding down a key until the message appears. To
temporarily pause a message, press the key again.

MAIN MENU

film

p1 pap

bal

MENU

PAPer

"pap" key select

Messages (top row)

Functions (bottom row)

Press keys simultaneously

Press and hold keyswitch to see help message

Keyswitch identification marks

«
...
11
12
13
14
15
...
»

Содержание 890





















































Отзывы:

Нет отзывов