manualshive.com logo in svg

X-Rite 890, Руководство по эксплуатации, Страница: 11 / 52

Поделиться
Скачать
X-Rite 890 Скачать руководство пользователя страница 11

 

G E T T I N G   S T A R T E D  

 

1-3 

APPLYING POWER 

To apply power to the instrument: 

1.

 

Verify that the voltage indicated on the adapter complies with the AC 
line voltage in your area. If not, contact X-Rite or your authorized 
representative. 

2.

 

Insert the small plug from the adapter into the power-input connector on 
the instrument.  

3.

 

Plug the detachable line cord into the adapter. 

4.

 

Plug the line cord into an AC wall receptacle. 

IMPORTANT:

 To extend the life of the internal memory battery, it is 

recommended that the instrument remain plugged into AC power. If you are 
using a modem, AC power must be applied in order to transmit or receive data. 

 

 

 

At initial power-up, the instrument performs a “boot memory test.” The 
testing sequence is displayed on the instrument screen. If all internal tests are 
OK, Page 1 Main Menu displays—see next page.  

Testing Program

boot memory...3

XRite 890  vXXXX

Copyrt 1989—1997

2
1

 

Power Input

Detachable Line Cord 

Adapter

Содержание 890





















































Отзывы:

Нет отзывов