X-Rite 890 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 52

X-Rite 890 Скачать руководство пользователя страница 33

5-1

S E C T I O N F I V E

Service and General

Maintenance

This section covers repair information, cleaning, general maintenance, and
troubleshooting tips for your instrument.

Section Five Contents

•

Repair

Information

•

Cleaning the Instrument

•

Replacing the Read Lamp

•

Troubleshooting

Tips

REPAIR INFORMATION

The X-Rite 890 is covered by a one-year limited warranty and should be
referred to the factory or an authorized service center for repairs within the
warranty period. Attempts to make repairs within this time frame may void
the warranty.

X-Rite provides a factory repair service to their customers. Because of the
complexity of the circuitry, all repairs should be referred to the factory or an
authorized service center (call: 1-888-826-3044).

X-Rite will repair any 890 instrument past warranty. Shipping cost to the
factory or authorized service center shall be paid by the customer, and the
instrument shall be submitted in the original carton, as a complete unaltered
unit.

«
...
31
32
33
34
35
...
»

Содержание 890





















































Отзывы:

Нет отзывов