X-Rite 890 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 52

X-Rite 890 Скачать руководство пользователя страница 41

B-1

A P P E N D I X B

Error Messages

Below is a list of typical error messages that can appear on your instrument’s
display screen. If any error messages listed, or not listed should appear, make
a note of it and take the appropriate steps to try to correct it. If an error
message is consistently displayed, contact X-Rite or an authorized service
center.

Message Reason

Possible

Cause

Solution

INVALID READING -
PLEASE RE-READ!

Unit did not
recognize strip.

Wrong strip selection.

Select correct format.

or

UNRECOGNIZABLE
STRIP

or

Strip did not have a
30.5mm (1.2”) leader
before first target.

Use strip with leader or refer
to the Control Strip & Balance
Print Format Guide for
leaderless strip insertion.

BUFFER OVERFLOW

(during measurement)

Strip not inserted in the
correct direction.

Refer to your Control Strip
and Balance Print Format
Guide for insertion direction.

Unit needs calibration

Calibrate instrument, Sec. 2.

Measurement

region

not aligned with center
diamond, or strip not
tracking properly.

Make sure measurement
patches are centered with
diamond and center line.
Usually setting the paper
guides to the numbers
indicated on the display takes
care of the problem. Make
sure strip feed straight through
unit and does not curve toward
one side.

One or more
measurement patches
are cloudy, have
excessive gradients, or
have flecks.

Process and then measure a
new strip.

NOTE:

If first read causes invalid error message, try

re-reading strip again. Measurement tolerances across the
patch are opened slightly on second read.

Motor drive roller
slippage due to restraint
or obstruction, or
contamination of rollers
from reading wet strips.

Remove restraint/obstruction
or dry drive rollers with air.

Lamp failure (weak or
bad).

Perform transmission
calibration to test lamp, Sec. 2.

«
...
39
40
41
42
43
...
»

Содержание 890





















































Отзывы:

Нет отзывов