background image

 

 

Original Operating Instructions 
BATx0280-ES-1-400-1 (Outdoor) 
User Information 

 

O_BATx0280-ES-1-400-1_(Outdoor)_V1.3_GB 

Page 

14

 of 

69

 

 

WARNING! 

Risk of injury due to fire or explosion! 

There is risk of fire and explosion if inflammable solvents are used. 

  Use only non-flammable solvents for cleaning. 

 

 

NOTICE 

Damage to components due to existing of termites! 

Termites can get into the product and damage the components. 

  Ensure that at the installation site and at the surrounding area 

no termites exist. 

  If the installation site is in a termite infested area, the termites 

must be eliminated with appropriate measures before product 
installation. 

 

 

NOTICE 

Damage to components due to ingress of dirt, dust and 
moisture as well as intrusion of pests and vermin! 

Ingress of dirt, dust, moisture and intrusion of pests and vermin can 
lead to damages of components. 

  After unpacking immediately mount all cable entry grommets. 

  Never leave the doors unattended open. 

  Open the doors only if it is absolutely necessary and close 

quickly. 

  Remove dust and water accumulation and all intruded pests 

and vermin as well as existing dirt (e.g. excrement, nests) 
from the interior area. 

  Place only baits and poisons in solid form or in containers in 

the product. 

  The use of baits and poisons in liquid, gas or powder form are 

not allowed. 

  Never connect and operate the product if the interior area is 

polluted, damp or/and infested with insects. 

  Before connecting the product baits and poisons as well as 

pests and vermin must be removed without trace. 

 

 

Содержание BAT 0280-ES-1-400-1 Series






































































Отзывы: