Out-1 Name EQ-1
->1000Hz +3.0dB Q= 3.5
Once in the Hi-Shelv_Q Filter's edit screen, all the filter's parameters can be modified using the “NAV/PM1”, “PM2”
and “PM3” encoders for editing the Filter's Low Cut Frequency, Gain and Q:
“
Low Cut Frequency
”: the selectable frequencies range is from 80Hz to 20kHz in steps of 1Hz and can be
adjusted by rotating the “NAV/PM1” encoder.
“
Gain
”: the selectable range of the Gain is from -12dB to +12dB in steps of 0.5 dB and can be adjusted by
rotating the “PM2” encoder.
“
Q
”: the selectable Q range is from 0.3 up to 20.0 in steps of 0.1 and can be adjusted by rotating the “PM3”
encoder.
When in the Parameters Editing Page, pushing once more the ENTER Button, it is possible to access the page of
the Frequency Fast Setting:
Out-1 Name EQ-1
->Edit Freq = 1000Hz
Here, the NAV/PM1” encoder will increment/decrement the Frequency value by step of one thousand Hz, the PM2
by steps of one hundred Hz and the PM3 by steps of one Hz.
Lo_Shelv_Q Filter:
These Symmetrical Shelving filters present ½ level of the selected Gain/Attenuation at the
selected cutting frequency, and a slope depending from the chosen Q value.
If we selected a Low Shelving filter with variable Q within EQ-1, then the GAIN has to be set at a desired value of
say +3dB using the PM2 encoder, the Q at 3.5 using the PM3 and the Hi Cut Frequency at say 1000Hz with the
NAV/PM1 encoder; the EQ sub-menu screen will show the following:
IOut-1 Name EQ-1
->1000Hz +3.0dB Q= 3.5
Once in the Lo-Shelv_Q Filter's edit screen, all the filter's parameters can be modified using the “NAV/PM1”, “PM2”
and “PM3” encoders for editing the Filter's High Cut Frequency, Gain and Q:
“
High Cut Frequency
”: the selectable frequencies range is from 80Hz to 20kHz in steps of 1Hz and can be
adjusted by rotating the “NAV/PM1” encoder.
“
Gain
”: the selectable range of the Gain is from -12dB to +12dB in steps of 0.5 dB and can be adjusted by
rotating the “PM2” encoder.
“
Q
”: the selectable Q range is from 0.3 up to 20.0 in steps of 0.1 and can be adjusted by rotating the “PM3”
encoder.
When in the Parameters Editing Page, pushing once more the ENTER Button, it is possible to access the page of
the Frequency Fast Setting:
Out-1 Name EQ-1
->Edit Freq = 1000Hz
Here, the NAV/PM1” encoder will increment/decrement the Frequency value by step of one thousand Hz, the PM2
by steps of one hundred Hz and the PM3 by steps of one Hz.
Note1
: once the desired options have been selected using the 3 encoders, they are automatically saved as current
and stored in the WS-P48 system status once leaving the page.
Note2
: to exit this page, push the “ESC” button.
Vu-Meter page
– from this page it is possible to select what is shown on the Output LED meters, by using the
“PM2” or “PM3” encoders.
The outputs' LED meters can show the Output signal LEVEL, the Output RMS Compressor's activity or the Output
Peak Limiters' activity.
When the Output signal Level is selected, the LED meters will show, from bottom up, the Level of the signal:
Out-1 Name Vu-Meter
-> Vu-Meter = Level
When the RMS Compressor's activity is selected, the LED meters will show, from top down, the activity of the
RMS Compressor Limiter on the output