background image

1

TABLE OF CONTENTS

WARRANTY  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY INFORMATION  . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12

SAFETY SIGNS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12

PREPARATION INSTRUCTIONS  . . . . . . . . . . . . . . . . . . . . 13-16

OPERATING INSTRUCTIONS  . . . . . . . . . . . . . . . . . . . . . . 17-19

OWNER SERVICE / SPECIFICATIONS  . . . . . . . . . . . . . . . . . . 20

TROUBLE-SHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . 21-22

PARTS LISTS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-29

TO THE OWNER:

Read this manual before using your Hydraulic Post Hole Digger. This manual is provided to give you the

necessary operating and maintenance instructions for keeping your post hole digger in top operating condition.
Please read this manual thoroughly. Understand what each control is for and how to use it. Observe all safety
signs on the machine and noted throughout the manual for safe operation of implement. Keep this manual handy
for ready reference.

Like all mechanical products, it will require cleaning and upkeep. Lubricate the Digger as specified.

Use only genuine Worksaver, Inc. service parts. Substitute parts will void the warranty and may not meet

standards required for safe and satisfactory operation. Record the model and serial number of your Post Hole
Digger here:

Model:________________________________________  Serial Number:_______________________________

RETAIL CUSTOMER’S RESPONSIBILITY

It is the Retail Customer and/or Operator’s responsibility to read the Operator’s Manual, to operate, lubri-

cate, maintain, and store the product in accordance with all instructions and safety procedures. Failure
of the operator to read the Operator’s Manual is a misuse of this equipment.

It is the Retail Customer and/or Operator’s responsibility to inspect the product and to have any part(s)

repaired or replaced when continued operation would cause damage or excessive wear to other parts or
cause a safety hazard.

It is the Retail Customer’s responsibility to deliver the product to the authorized Worksaver Dealer, from

whom he purchased it, for service or replacement of defective parts which are covered by warranty.
Repairs to be submitted for warranty consideration must be made within forty-five (45) days of failure.

It is the Retail Customer’s responsibility for any cost incurred by the Dealer for traveling to or hauling

of the product for the purpose of performing a warranty obligation or inspection.

SI NO LEEINGLES, PIDA AYUDA A
AIGUIEN QUE SI LO LEA PARA QUE
LE TRADUZCA LAS MEDIDAS DE
SEGURIDAD.

STATEMENT

OF POLICY

It is the policy of Worksaver,

Inc. to improve its products
where it is possible and practical
to do so.

Worksaver, Inc.

reserves the right to make
changes or improvements in
design and construction at any
time, without incurring the obliga-
tion to make these changes on
previously manufactured units.

Содержание 614HC
































Отзывы: