Woods 208-2 страница 4 Скачать руководство пользователя | Manualshive

Страница: 4 / 74

background image

2

Introduction

32394 (Rev. 9/3/2004)

SPECIFICATIONS

M208-2

M208-2

208-2

Mounted

Mounted

Pull-Type

(Single Tailwheel)

(Dual Tailwheel)

Recommended Tractor Size

40-80 HP

60-80 HP

60-80 HP

Weight (Approximate)

1650 lbs.

1400 lbs.

1460 lbs.

Wheel Size

15" Rims or 16"

16" OD Solid

16" OD Solid

OD Solid Tires

Caster Wheel

Caster Wheel

Wheel Tread

Adjustable

Non-Adjustable

Non-Adjustable

208-2 Pull-Type and M208-2 Mounted

Blades, Heat-Treated Alloy Steel

3/8" x 4"

Blade Rotation Direction

Left Spindle: CCW

Right Spindle: CW

Blade Tip Speed (ft./minute)

540 RPM = 13,520

Cutting Height Range

2 to 12 inches

Cutting Swath

8 ft. (96") (4-1/4" overlap)

Driveline

Cat IV Joint with slip clutch and torsion bar protection

Gearbox Rating (Spindle Boxes)

80 HP with heat-treated alloy steel gears, heat-treated
vertical shafts and lubricated tapered roller bearings

(Input Box)

80 HP

Function

The 208-2 & M208-2 model cutters are designed for mowing
large areas of grass, crop residue or brush up to 1-1/2"
diameter.

GENERAL INFORMATION

The purpose of this manual is to assist you in operating
and maintaining your cutter. Read it carefully. It fur-
nishes information and instructions that will help you
achieve years of dependable performance. These
instructions have been compiled from extensive field
experience and engineering data. Some information
may be general in nature due to unknown and varying
operating conditions. However, through experience
and these instructions, you should be able to develop
procedures suitable to your particular situation.

The illustrations and data used in this manual were cur-
rent at the time of printing but, due to possible inline
production changes, your machine may vary slightly in
detail. We reserve the right to redesign and change the
machines as may be necessary without notification.

■

Some illustrations in this manual show the cut-

ter with safety shields removed to provide a better
view. The cutter should never be operated with any
safety shielding removed.

Throughout this manual, references are made to right
and left direction. These are determined by standing
behind the equipment facing the direction of forward
travel. Blade rotation is clockwise (right) and counter-
clockwise (left) as viewed from the top of the cutter.

WARNING

«
...
2
3
4
5
6
...
»

Содержание 208-2











































































Отзывы:

Нет отзывов

Похожие инструкции для 208-2

Бренд: B&K Страницы: 5

Бренд: B&K Страницы: 28

Бренд: TC Electronic Страницы: 2

Бренд: Bahco Страницы: 131

Бренд: Bahco Страницы: 126

Бренд: SAMCHULLY Страницы: 48

Бренд: HAGS Страницы: 5

Бренд: HAGER WERKEN Страницы: 2

Бренд: Taylor Страницы: 60

Бренд: TANDBERG Страницы: 23

Бренд: Backyard Play Systems Страницы: 73

Бренд: Task Force Tips Страницы: 20

Бренд: Yamaha Страницы: 4

Бренд: Wacker Neuson Страницы: 120

Carestation 620

Бренд: GE Страницы: 268

Бренд: GE Страницы: 50

Бренд: Kelvin Страницы: 30

Бренд: Marani Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды