manualshive.com logo in svg

Woods 208-2, Руководство оператора, Страница: 16 / 74

Поделиться
Скачать
Woods 208-2 Скачать руководство пользователя страница 16

14 

Operation

32394 (Rev. 9/3/2004)

the opposite cutting edge of the blade. All blades,
except the reversible blades, are for a specific spindle
rotation. Be sure they are installed on the correct spin-
dle. Refer to the Owner Service section for blade instal-
lation.

TRANSPORTATION LOCK

To ready unit for transport, raise cutter with hydraulic
cylinder or ratchet. Lift transport bar and insert clevis
pin in slot "A" when it lines up with hole in lifting lug.

For normal operation, remove pin from transport bar
and insert into hole "B" and lower transport bar to
wheel yoke.

The clevis pin and hairpin are attached with a chain to
ensure they are available when required.

The transport bar should also be locked in the raised
position and the cutter should be securely blocked
before working underneath cutter. Failure to install
safety devices could result in unit dropping unexpect-
edly.

„

Never go underneath equipment (lowered to the

ground or raised) unless it is properly blocked and
secured. Never place any part of the body under-
neath equipment or between moveable parts even
when the engine has been turned off. Hydraulic
system leak down, hydraulic system failures,
mechanical failures, or movement of control levers
can cause equipment to drop or rotate unexpect-
edly and cause severe injury or death. Follow Oper-
ator's Manual instructions for working underneath
and blocking requirements or have work done by a
qualified dealer.

 Figure 4

. Transport Lock

WARNING

DC2994B

RAISED TRANSPORT
POSITION

OPERATING
POSITION

1. Clevis pin and chain
2. Cotter pin
3. Hydraulic cylinder
4. Tailwheel height adjustment post
5. Washer
6. Transport bar

Содержание 208-2











































































Отзывы:

Нет отзывов