Woods 208-2 Скачать руководство пользователя страница 49

Страница: 49 / 74

Parts

32394 (Rev. 9/3/2004)

208-2 REAR DRIVE ASSEMBLY WITH SPLINED TELESCOPIC SHAFT (PULL-TYPE UNITS)

1--COMPLETE DRIVE WITH CLUTCH

CD5027A

24--COMPRESSION SPRING REPAIR KIT

NOTE: Four Styles of driveshafts have
been used on the 208 series cutters.
Check your driveshaft for square, splined,
tri-lobe, or two-lobe shape and order
repair parts from the correct parts list.

REF

PART

QTY

DESCRIPTION

53497

Drive assembly complete (includes
items 2 - 23)

12128

Ring snap .062 x 72mm

13133

1-1/2 Ball bearing

2985

1/4 - 28 Threaded 90° grease fitting

55140

Tubular shaft 1-5/16 - 20 splined 45-
1/2 long

13132

3-Joint drive bearing housing assem-
bly (includes items 2, 3, 4)

52394

Shield bearing kit

55142

Shield 2.75 x 2.03 x 38.9 (includes
item 7)

55141

Shield 3.02 x 2.84 x 28.75 (includes
item 7)

55139

1-5/16 Spline 30 long/ Yoke and
Shaft 35

110

U-Joint cross and bearing kit 35

13931

6S Clutch back-up plate

19459

Friction disc 4 x 6.15

13928

6S Clutch yoke and plate 35

13933

6S Clutch hub 1-1/2 with bushing

11576

1-7/16 x 1-5/8 x 9/16 Bronze bushing
(includes item 7)

12914

3/8 NC Wide flanged locknut

29687

Compression spring 1.15 x .26 x 2.2

13927

3/8 NC x 3-3/4 HHCS GR5

23141

5/8 NC x 3-1/2 HHCS HT

6239

5/8 NC Hex locknut

6048

7/16 NC x 3-1/2 HHCS

13921

7/16 NC Hex locknut

7283

Compression spring repair kit
(includes items 17, 18 & 19)

REF

PART

QTY

DESCRIPTION

Содержание 208-2











































































Результаты поиска

Содержание 208-2

Отзывы:

Woods 208-2, Руководство оператора, Страница: 49 / 74

Результаты поиска

Содержание 208-2

Отзывы: