Woods 208-2 страница 29 Скачать руководство пользователя | Manualshive

Страница: 29 / 74

background image

Dealer Service

27

32394 (Rev. 9/3/2004)

3.

Clamp cup in vise as shown in Figure 16 and tap
on yoke to completely remove cup from yoke.
Repeat Step 2 & Step 3 for opposite cup.

Figure 16

4.

Place universal cross in vise as shown in Figure 17
and tap on yoke to remove cup. Repeat Step 3 for
final removal. Drive remaining cup out with a drift
and hammer.

Figure 17

U-Joint Assembly

1.

Place seals securely on bearing cups. Insert cup
into yoke from outside and press in with hand
pressure as far as possible. Insert journal cross
into bearing cup with grease fitting away from
shaft. Be careful not to disturb needle bearings.
Insert another bearing cup directly across from first
cup and press in as far as possible with hand
pressure.
Trap cups in vise and apply pressure. Be sure
journal cross is started into bearings and continue
pressure with vise, squeezing in as far as possible.
Tapping the yoke will help.

2.

Seat cups by placing a drift or socket (slightly
smaller than the cup) on cup and rap with a
hammer. See Figure 18. Install snap ring and
repeat on opposite cup.

3.

Repeat Step 1 & Step 2 to install remaining cups in
remaining yoke.
Move both yokes in all directions to check for free
movement. If movement is restricted, rap on yokes
sharply with a hammer to relieve any tension.
Repeat until both yokes move in all directions
without restriction.

Figure 18

CD1387

CD1388

CD1389

«
...
27
28
29
30
31
...
»

Содержание 208-2











































































Отзывы:

Нет отзывов

Похожие инструкции для 208-2

Бренд: B&K Страницы: 5

Бренд: B&K Страницы: 28

Бренд: Unex Страницы: 5

Бренд: AAON Страницы: 36

Бренд: Daga Страницы: 24

Бренд: DAF Страницы: 68

Бренд: Federal Signal Corporation Страницы: 4

Бренд: ParaBody Страницы: 7

Бренд: HANYOUNG NUX Страницы: 2

Бренд: NEILPRYDE Страницы: 55

Бренд: HANYOUNGNUX Страницы: 4

Бренд: Park House Healthcare Страницы: 6

Бренд: J&M Страницы: 33

Бренд: Olsen Страницы: 58

Бренд: Gaspardo Страницы: 88

Бренд: ZacUrate Страницы: 2

Бренд: ZacUrate Страницы: 2

Бренд: Waves Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды