background image

Page 26

Remove the Manifold

1

Use a 

1

/

4

" combination wrench to remove the manifold

screw from each valve.

2

Use a 

5

/

8

” combination wrench to remove the manifold inlet

line from the brass elbow on the manifold.

3

Remove any tie wraps that are holding parts of the wire
harness to the manifold.

4

Remove the manifold from the manifold bracket.

MANIFOLD INSTALLATION

Install the Manifold

1

Use a 

5

/

8

” combination wrench to attach the manifold inlet

line to the brass elbow on the manifold.

2

Use a 

1

/

4

” combination wrench to install the manifold screw

on each valve.

Note: The brass elbow is included on the new manifold.

  CAUTION

Do not lift the manifold to remove the tube fittings.
Gas tubes provide support to the manifold.
Deforming the gas tube may cause knob alignment
issues.

  WARNING

When reassembling manifold components, only pipe
thread compound should be used. Do not use Teflon
tape to seal gas connections.

Install All Receptacles

To install each receptacle:

1

Install the receptacle onto the burner valve.

2

Use a Phillips screwdriver to install the mounting screws
into the receptacle.

Install the Burner Pan

Place the burner pan on the burner box.

Install All Burner Assemblies

To install each burner assembly:

1

Attach the electrode wire to the igniter.

2

Place the burner assembly into the burner pan.

3

Use a T-15 Torx bit to install the screws holding the burner
assembly to the orifice holder, torqued to 24 in lb.

Install All Bezels

To install each bezel:

1

Connect the bezel to the light wire harness.

2

Insert the bezel into the unit.

3

Twist the bezel 90° clockwise.

Install All Knobs

Push each knob onto each valve shaft.

Install All Burner Caps

Install all burner caps onto the burner assemblies.

Install All Burner Grates

Place all burner grates onto the cooktop.

ELECTRODE WIRE REMOVAL

To remove the electrode wire, first remove the burner grate,
burner cap, and burner assembly.

  WARNING

Turn off the power to the product before starting this
procedure.

CG Professional Gas Cooktop Service Manual

 

service.subzero.com

828386 REV. A     06/2018

25

 

Содержание CG Series



































Отзывы: