wiwa HERKULES PFP Скачать руководство пользователя

Страница: 20 / 40

Translation of the original operation manual

HERKULES PFP

HERKULES PFP_BAoDB_en_1402_B · rs

Transportation, installation and assembly

4 Transportation, installation and assembly

The unit left the factory in flawless condition and was appropriately packed for

transportation.

Check the unit on receipt for any damage in transit and for completeness

4.1 Transportation

Please follow these notes when transporting the unit:

➤

Ensure sufficient load bearing capacity of lifting gear and lifting tackle when

loading the unit. You will find the dimensions and weights of the unit on the

machine card.

➤

The unit must only be lifted by the lifting and lashing points provided for this

purpose.

➤

Caution danger of tipping! Ensure even load distribution to secure the sys-

tem against tipping over.

➤

Do not transport any other objects (e.g. material drums) while lifting or

loading the unit.

➤

Never stand under suspended loads or inside the loading area.

This poses a life hazard!

➤

Secure the load on the transport vehicle against slipping and falling off.

If the unit was already operated, please observe the following:

➤

Disconnect the entire system power supply – even for short transportation

distances.

➤

Empty the unit before transportation – fluid residues may escape during

transportation despite this measure.

➤

Remove all loose parts (e.g. tools) from the unit.

➤

Assemble the parts or fittings dismantled for transport purposes before start

up and in compliance with the intended use of the system.

4.2 Installation location

The

HERKULES PFP

can be installed inside and outside spray booths. However,

outdoor installation should be preferred in order to avoid contamination.

WARNING
If the unit is used outside during a thunderstorm, a lightning strike can cause

a life-threatening situation for the operating personnel.

➤

Do not operate a unit out of doors during a thunderstorm!

➤

The unit owner must ensure that the unit is equipped with suitable light-

ning protection equipment.

Set the unit up horizontally on a foundation that is flat, firm and vibration-free.

The unit must not be tipped or on an incline. Ensure that all the operating

elements and safety features are easy to reach.

Содержание HERKULES PFP









































Результаты поиска

Содержание HERKULES PFP

Отзывы:

Похожие инструкции для HERKULES PFP

Бренды по названию

Популярные бренды

wiwa HERKULES PFP, Руководство по эксплуатации

Результаты поиска

Содержание HERKULES PFP

Отзывы:

Похожие инструкции для HERKULES PFP

Бренды по названию

Популярные бренды