WITTUR sematic DC-PWM Compatible Скачать руководство пользователя

Страница: 27 / 42

www

.wittur

.com

Changes can be made without notice

PM.2.004923.EN - 811-000-000 SDS

DC-PWM Compatible · Edition 22 July 2020

Drive - Instruction Manual

8 GENERAL OPTION

•

Connect the handset to RJ45 connector;

•

If necessary, using keys

and

choose the required language and confirm with the “OK” key

•

Using keys

and

run through the MAIN MENU and choose GENERAL OPTIONS

•

Press OK to confirm the choice

•

The GENERAL OPTION menu allows the Door Controller to operate by means of the following parameter options:

−

REVERSING SYSTEM

−

MAIN LIFT CONTROLLER TEST

−

NO MLC SIGNAL

−

MLC INPUT ALARM

−

LIMITED DOOR REVERSAL

−

CAR DOOR LOCKING DEVICE

−

GLAZED PANELED DOORS

−

AUX OUTPUT RELAY

−

PROTECTIVE DEVICE LOGIC

−

EMULATION TYPE

These parameter meanings and settings are detailed in the following paragraphs.

8.1 REVERSING SYSTEM SETTING BY MEANS OF THE HANDSET

•

See

“6.1 Reversing system force setting” a pag. 19

for the meaning of this parameter

•

Using keys

and

run through the GENERAL OPTIONS and choose the option REVERSING SYSTEM

•

Press the “OK” key to confirm the choice

•

The following options are viewed on the display:

−

INTERNAL

−

EXTERNAL

•

Using keys

and

choose the required option and press the “OK” key to confirm it

•

The display shows the confirmed option and restores the menu GENERAL OPTIONS

•

The following options are available:

−

“BACK”: Press key F1 to restore the menu GENERAL OPTIONS

−

“MENU”: Press key F3 to restore the MAIN MENU

8.2 ACTIVATION OF THE MAIN LIFT CONTROLLER TEST BY MEANS OF THE HANDSET

•

See

“6.4 Main Lift Controller Test” a pag. 19

for the meaning of this parameter

•

Using keys

and

run through the GENERAL OPTIONS and choose the option MAIN LIFT CONTROLLER TEST

•

Press the “OK” key to confirm the choice

•

The following options are viewed on the display:

−

WHEN MOVING

•

The display shows the confirmed option and restores the menu GENERAL OPTIONS

•

The following options are available:

−

“BACK”: Press key F1 to restore the menu GENERAL OPTIONS

−

“MENU”: Press key F3 to restore the MAIN MENU

8.3 ACTIVATION OF THE MAIN LIFT FAILURE BY MEANS OF THE HANDSET

•

See

“6.4.1 No MLC Signal” a pag. 19

for the meaning of this parameter

•

Using keys

and

run through the GENERAL OPTIONS and choose the option NO MLC SIGNAL

•

Press the “OK” key to confirm the choice

•

The following options are viewed on the display:

−

IMMEDIATELY STOP

•

The display shows the confirmed option and restores the menu GENERAL OPTIONS

•

The following options are available:

−

“BACK”: Press key F1 to restore the menu GENERAL OPTIONS

−

“MENU”: Press key F3 to restore the MAIN MENU

8.4 MAIN LIFT CONTROLLER ALARM - (MLC INPUT ALARM)

•

See

“6.4.2 Main Lift Controller Input Alarm” a pag. 19

for the meaning of this parameter

•

Using keys

and

, run through the GENERAL OPTIONS and choose the option MLC INPUT ALARM

•

Press key “OK” to confirm the choice

•

The following options are viewed on the display:

−

OFF

−

•

Using keys

and

, choose the required option and press the “OK” key to confirm it

•

The display shows the confirmed option and restores the menu GENERAL OPTIONS

•

The following options are available:

−

“BACK”: Press key F1 to restore the menu GENERAL OPTIONS

−

“MENU”: Press key F3 to restore the MAIN MENU

8.5 LIMITED DOOR REVERSAL ACTIVATION BY MEANS OF THE HANDSET

•

See

“6.3 Limited Door Reversal” a pag. 19

for the meaning of this parameter

Содержание sematic DC-PWM Compatible











































Результаты поиска

Содержание sematic DC-PWM Compatible

Отзывы:

Похожие инструкции для sematic DC-PWM Compatible

Бренды по названию

Популярные бренды

WITTUR sematic DC-PWM Compatible, Инструкция по эксплуатации

Результаты поиска

Содержание sematic DC-PWM Compatible

Отзывы:

Похожие инструкции для sematic DC-PWM Compatible

Бренды по названию

Популярные бренды