Wisenet PNM-9322VQP Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 28

background image

English _

13

!

INST

ALLA

TION & CONNECTION

Preparing & Installing Camera Bracket

For installation guidelines for brackets and housings, refer to the installation manual that is enclosed with the
bracket or housing.

`

Available Bracket Models

Model

Item

SBP-390WM2

Wall Mount

SBP-300CMW

Ceiling Mount

SBP-300LMW

Parapet Mount

SBP-300KMW

Corner Mount

SBP-300PMW

Pole Mount

Attaching to the unbundled adapter

Choose and purchase a necessary one of the following options (unbundled) that is suitable to the installation
site or for your convenience.
See “

Optional Accessories for Installation

” for separately sold products. (Page 8)

1.

Pass the cables externally exposed through a wall or pole
mount through the installation base.

2.

Turn the installation base in the direction of the arrow to
join it to the mount.

M

`

If the product is installed in an area where outside moisture
can penetrate through the mount, use the provided cable
bushing to block the inflow of outside moisture.

-

Coat the cable bushing with an appropriate amount of
grease and connect the cable to the correct hole of the
cable bushing. Plug the remaining holes not penetrated by
cables with the pins.

-

Inside the installation base, plug the cable bushing in the joint hole.
When plugging it in, press the whole bushing area evenly so that it is
properly plugged into the hole.

Wall Mount or
Pole Mount

Installed base

Joint

Cable

PIN

Other Cables

Cable bushing

Ethernet Cable

«
...
11
12
13
14
15
...
»

Содержание PNM-9322VQP





























Отзывы:

Нет отзывов

Похожие инструкции для PNM-9322VQP

Бренд: Tamron Страницы: 8

Бренд: 2gig Technologies Страницы: 8

Бренд: 2gig Technologies Страницы: 2

Бренд: Messoa Страницы: 32

Бренд: Federal Signal Corporation Страницы: 24

Бренд: Datalogic Страницы: 7

Бренд: e-Line Technology Страницы: 36

ED 14-42mm f3.5-5.66 EZ

Бренд: Olympus Страницы: 15

Бренд: GST Страницы: 11

Бренд: S Fire Страницы: 6

Бренд: Geutebruck Страницы: 2

Бренд: ADT Страницы: 14

Бренд: Salray Works Страницы: 69

Бренд: 3xLogic Страницы: 23

Binswitch Elite BSE1V10C

Бренд: 4B Страницы: 12

Бренд: Vaxcel Страницы: 7

Бренд: e-Line Technology Страницы: 2

Бренд: BUCKINGHAM MFG Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды