Windsor Saber Cutter 10052360 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 92

background image

MAINTENANCE

CUTTER 24V 86036830 06/20/07

4-7

TO ADJUST SQUEEGEE PITCH

1.

Choose a smooth, level surface. Turn “ON” the
key switch. Lower the squeegee and drive
forward at least 2 feet (60cm.).

2.

With the squeegee down, stop the machine. Do
not allow machine to roll back.

FOR SAFETY: Before leaving or servicing the
machine; stop on level surface, turn off machine
and remove key.
3.

Determine the differences, if any, in deflection of
the squeegee blade between each end and the
middle. Proper adjustment is obtained when
deflection is equal all the way across the
squeegee blade. The bubble level should also
indicate when the squeegee is adjusted
properly. When the air bubble is in the center of
the vial, the deflection should be even across
the squeegee blade.

4.

To decrease the deflection of the squeegee
blade at the ends, tighten knob near the
squeegee center. To increase the deflection at
the ends of the squeegee assembly, loosen
knob.

5.

Check the deflection of the squeegee blades
again. Repeat steps 1 through 4 until the
deflection is equal across the entire rear
squeegee blade.

TO ADJUST AMOUNT OF REAR
SQUEEGEE DEFLECTION

1.

Choose a smooth, level surface. Lower the
squeegee and drive forward at least 2 feet
(60cm).

2.

With the squeegee down, stop the machine. Do
not allow machine to roll back.

FOR SAFETY: Before leaving or servicing
machine; stop on level surface, turn off machine
and remove key.

3.

Observe the amount of squeegee deflection. It
should deflect 3/8 in. (9.5mm) across the entire
width of the squeegee.

4.

To increase the squeegee deflection, turn the 2
knobs at the squeegee ends counter-clockwise.
To decrease the deflection, turn the knobs
clockwise.

NOTE: The deflection should be consistent along
the length of the squeegee. If the deflection varies
from end to end the knobs can be adjusted
independently to correct the variation.
5.

Turn on the key switch. Raise, then lower
squeegee assembly. Drive forward at least
2 feet (60cm).

6.

Repeat steps 2 through 4 until deflection of
3/8 in. (9.5mm) is reached.

3.

TO REPLACE AQUA-MIZER
SQUEEGEE BLADES

These squeegee blades have two wear edges. To
use the second edge:

1.

Remove deck shrouds.

2.

Remove brushes or pad drivers.

3.

Remove each of the Aqua-Mizer squeegee
systems.

4.

Remove the hardware from each system that
retains the blade.

5.

Flip the blades and replace hardware.

6.

Re-install each Aqua-Mizer system, brushes or
pad drivers and shrouds.

3/8”

PROPER DEFLECTION OF SQUEEGEE BLADE

«
...
23
24
25
26
27
...
»

Содержание Saber Cutter 10052360





























































































Отзывы:

Нет отзывов

Похожие инструкции для Saber Cutter 10052360

Scrubmaster B 120 R

Бренд: HAKO Страницы: 10

Бренд: Kärcher Страницы: 604

Бренд: MW TOOLS Страницы: 5

Бренд: American-Lincoln Страницы: 160

Бренд: Renfert Страницы: 303

Бренд: Pacific Страницы: 6

Бренд: Quest Engineering Страницы: 9

Scrubmaster B175 R

Бренд: HAKO Страницы: 2

Scrubmaster B25

Бренд: HAKO Страницы: 52

Бренд: lavina Страницы: 33

Бренд: R.P.S. Corporation Страницы: 98

Бренд: ulsonix Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды