Windsor Saber Cutter 10052360 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 92

background image

MACHINE OPERATION

CUTTER 24V 86036830 06/20/07

3-9

PRE-RUN MACHINE INSPECTION

Do a pre-run inspection to find possible problems that
could cause poor performance or lost time from
breakdown. Follow the same procedure each time to
avoid missing steps.

NOTE: See maintenance section for pre-run machine
inspection checklist items.

STARTING MACHINE

NOTE: Perform pre-run machine check before
operating machine.
FOR SAFETY: Before starting machine, make
sure that all safety devices are in place and
operating properly.

1.

Turn the machine power on.

2.

Release the parking brake, if your machine is
equipped with this option.

3.

Engage the direction propel levers for the desired
direction.

EMERGENCY STOP PROCEDURES

1.

Release the propel levers.

2.

Turn machine power off with key switch.

3.

If an electrical problem is suspected push in
emergency stop button, if machine is equipped
with this option.

4.

Apply brakes, if your machine is equipped with
this option.

FILLING SOLUTION TANK

FOR SAFETY: Before leaving or servicing
machine; stop on level surface, turn off machine
and remove key.

1.

Turn the machine power off.

2.

Set the parking brake if your machine is equipped
with this option.

3.

Remove solution tank cover.

4.

Fill the solution tank with clean water, leaving
enough room for the required amount of cleaning
solution. The solution tank capacity filled to 2” (5
cm) from bottom of fill inlet is 23 gallons (87 liters).
The water must not be hotter than 140

°

F (60

°

C)

to prevent damage to the tank.

5.

Measure the chemical into the solution tank.
Liquid chemicals should be added to the solution
tank after filling with water. Dry chemicals should
be thoroughly mixed before being added into
solution tank. Commercially available, high
alkaline floor cleaners, are suitable for use in the

solution system.

NOTE: Read the chemical manufacturers
recommended proportion instructions.

6.

Replace solution tank cover.

Flammable materials can cause an explosion or
fire. Do not use flammable materials in the tanks.

!

WARNING

«
...
14
15
16
17
18
...
»

Содержание Saber Cutter 10052360





























































































Отзывы:

Нет отзывов

Похожие инструкции для Saber Cutter 10052360

Бренд: IPC Страницы: 2

Бренд: Kärcher Страницы: 19

B 110 R Classic Bp D75

Бренд: Kärcher Страницы: 316

Бренд: Tornado Страницы: 47

Бренд: ADIATEK Страницы: 21

IDATA-HDMI-EA74K

Бренд: Techly Страницы: 8

Бренд: CorroVenta Страницы: 4

Бренд: Teka Страницы: 24

Бренд: U.S. Products Страницы: 44

KM 130/300 R LPG

Бренд: Kärcher Страницы: 32

Бренд: Ace Страницы: 13

Бренд: Neilsen Страницы: 8

Extreme MXE-200

Бренд: Nautilus Страницы: 55

Бренд: Miele Страницы: 57

Powr-Flite PAS17BA

Бренд: Tacony Страницы: 9

Бренд: Sprintus Страницы: 2

Бренд: Windsor Страницы: 45

Бренд: Victor Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды