Windsor Saber Cutter 10052360 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 92

Windsor Saber Cutter 10052360 Скачать руководство пользователя страница 29

MAINTENANCE

CUTTER 24V 86036830 06/20/07

4-11

11. VACUUM MOTOR

(Refer to the Vacuum Group in the parts section of
manual)

Do not use a pressure washer to clean around the
vacuum motors. Use tap pressure only. Care
must be taken so that water is not directed into
vacuum motor air intakes.

CHANGING VACUUM MOTOR

1.

Remove side cover.

2.

Disconnect electrical connector to the vacuum
motor.

3.

Loosen clamp and disconnect hose from vacuum
intake.

4.

Remove vacuum motor mounting bracket bolts,
which are located under frame.

5.

Remove vacuum motor and mounting bracket
assembly.

6.

Reverse steps to install

!

WARNING

Vacuum Motor Carbon Brushes Replacement (Windsor)

End Cap

Carbon
Brushes

If armature commutator is grooved, extremely pitted or not
concentric, the motor will need to be replaced or sent to a
qualified service center.

Important:

These brushes wear quicker as the length shortens
due to increased heat. Spring inside brush housing
will damage motor if brushes are allowed to wear
away completely.

Periodically check the length of the carbon brushes.
Replace both carbon brushes when either is less than
3/8" (9.5mm) long.

3
8

[9.5mm]

Important:

These brushes wear quicker as the length shortens
due to increased heat. Spring inside brush housing
will damage motor if brushes are allowed to wear
away completely.

Periodically check the length of the carbon brushes.
Replace both carbon brushes when either is less than
3/8" (9.5mm) long.

3/8 (9.5mm)

Vacuum Motor Carbon Brushes Replacement (Ametek)

End Cap

Carbon
Brushes

If armature commutator is grooved, extremely pitted or not
concentric, the motor will need to be replaced or sent to a
qualified service center.

Note:
Place
stop in
groove.

«
...
27
28
29
30
31
...
»

Содержание Saber Cutter 10052360





























































































Отзывы:

Нет отзывов