manualshive.com logo in svg

Winco Elevate BDC 2578, Руководство владельца по эксплуатации и обслуживанию

Поделиться
Скачать
Winco Elevate BDC 2578 Скачать руководство пользователя страница 31

FIG 1

Page 31 of 49

Document No.: 006020 
Revision: P 

OWNERS OPERATING & MAINTENANCE MANUAL

PHLEBOTOMY COLLECTION

SEAT INSTALLATION

FAILURE TO COMPLETELY TIGHTEN THE SEAT MOUNTING 

SCREWS COULD RESULT IN SERIOUS INJURY.

1. 

Position 

Chair Frame

 in upright position. Check tightness of all installed screws, bolts, nuts and 

other fasteners in case they loosened during shipping.

2. 

Align the screws on bottom of the 

Seat Assembly

, with the 

Seat Support holes

. (Hole spacing of 

Seat Supports will be narrower toward front of Chair). 

Seat

 can only be properly installed facing one 

direction.  

Be sure that all (4) Seat Screws go completely through the Seat Support straps on 

chair frame. (FIG 1)

3. 

Install four (4) 

lock nuts

 to the screws on the 

Seat Assembly

 and completely tighten with 7/16” 

wrench. (

FIG 1

)

2578

Содержание Elevate BDC 2578





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды