Winco Elevate BDC 2578 Скачать руководство пользователя страница 3

Страница: 3 / 52

Page 3 of 49

Document No.: 006020
Revision: P

OWNERS OPERATING & MAINTENANCE MANUAL

PHLEBOTOMY COLLECTION

READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS

BEFORE USING THIS PRODUCT!

Do NOT install, maintain or operate this equipment without reading and following
this manual, otherwise injury and/or damage may result.

IF YOU HAVE ANY QUESTIONS OR CONCERNS,

PLEASE CONTACT WINCO MFG., LLC.

Winco assumes no responsibility for damage or injury caused by improper
assembly, installation, use, or maintenance of these products.

No part of this manual may be duplicated in any form without the prior consent of
Winco Mfg., LLC. Unauthorized duplication / distribution of these materials may
result in civil prosecution to the maximum extent allowed by law.

The information contained in this manual is subject to change without notice.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE!

These instructions are available online at no charge.

Visit wincomfg.com to download.

Содержание Elevate BDC 2578





















































Результаты поиска

Содержание Elevate BDC 2578

Отзывы:

Бренды по названию

Популярные бренды

Winco Elevate BDC 2578, Руководство владельца по эксплуатации и обслуживанию

Результаты поиска

Содержание Elevate BDC 2578

Отзывы:

Бренды по названию

Популярные бренды