manualshive.com logo in svg

Winco Elevate BDC 2578, Руководство владельца по эксплуатации и обслуживанию

Поделиться
Скачать
Winco Elevate BDC 2578 Скачать руководство пользователя страница 24

FIG 3

Page 24 of 49

Document No.: 006020 
Revision: P 

OWNERS OPERATING & MAINTENANCE MANUAL

PHLEBOTOMY COLLECTION

1. 

Position 

Chair Frame

 in upright position. Check tightness of all installed screws, bolts and nuts in 

case they loosened during shipping.

2. 

Align the screws on bottom of the 

Seat Assembly

, with the 

Seat Support holes

. (

FIG 3) 

NOTE: Seat Supports

 are angled to give the seat a very slight recline angle. The 

FRONT

 of seat 

should be positioned toward the 

HIGHER

 end of the strap. (

FIG 3) 

 

Be sure that all (4) Seat Screws go completely through the Seat Support straps on chair frame.

3. 

Install four (4) 

lock nuts

 to the screws on the 

Seat Assembly

 and completely tighten with 7/16” 

wrench.

SEAT INSTALLATION

FAILURE TO COMPLETELY TIGHTEN THE SEAT MOUNTING 

SCREWS COULD RESULT IN SERIOUS INJURY.

Содержание Elevate BDC 2578





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды