Wilo Control EC-L Скачать руководство пользователя страница 5

Страница: 5 / 64

Installation and operating instructions • Wilo-Control EC-L • Ed.04/2022-09

DANGER

Type and source of the danger!

Consequences of the danger and instructions for avoidance.

•

Safety instructions relating to property damage start with a
signal word and are displayed

without

a symbol.

CAUTION

Type and source of the danger!

Consequences or information.

Signal words

•

Danger!

Failure to observe safety instructions will result in serious injury
or death!

•

Warning!

Failure to follow instructions can lead to (serious) injury!

•

Caution!

Failure to follow instructions can lead to property damage and
possible total loss.

•

Notice!

Useful information on handling the product

Markups

✓

Prerequisite

Work step/list

⇒

Notice/instructions

▶

Result

Symbols

These instructions use the following symbols:

Danger of electric voltage

Danger – explosive atmosphere

Useful information

2.2

Personnel qualifications

•

Personnel have been instructed on locally applicable regula-
tions governing accident prevention.

•

Personnel have read and understood the installation and oper-
ating instructions.

•

Electrical work: qualified electrician
Person with appropriate technical training, knowledge and ex-
perience who can identify and prevent electrical hazards.

•

Installation/dismantling work: qualified electrician
Knowledge regarding tools and fixation material for various
structures

Содержание Control EC-L

































































Результаты поиска

Содержание Control EC-L

Отзывы:

Похожие инструкции для Control EC-L

Бренды по названию

Популярные бренды

Wilo Control EC-L, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Control EC-L

Отзывы:

Похожие инструкции для Control EC-L

Бренды по названию

Популярные бренды