background image

4

IMPORTANT SAFETY INFORMATION

 

Warning! Damage to health due to infectious liquids and 

 pathogenic germs.

•   When handling infectious liquids and pathogenic germs, observe 

the national regulations, the biosafety level of your laboratory, the 

material safety data sheets, and the manufacturer’s application 

notes. 

 

•   Wear your personal protective equipment.
•   For comprehensive regulations about handling germs or biological  

material of risk group II or higher, please refer to the “Laboratory  

Biosafety Manual” (source: World Health Organisation, Laboratory  

Biosafety Manual, the current edition).

IMPORTANT SAFETY INFORMATION

INFORMATION ON PRODUCT LIABILITY

In the following cases, the designated protection of the device may be affected.  

Liability for any resulting damage or personal injury is then transferred to the 

owner:
•  The device is not used in accordance with the operating manual.
•  The device is used outisde of its intended use.
•  The device is used with accessories or consumables that are not 

recommended by Williams Refrigeration.

•  The device is maintained or repaired by persons not authorised by Williams 

Refrigeration.

•  The user makes unauthorised changes to the device.

Содержание Medi+ LWMP620

















Отзывы: