background image

3

IMPORTANT SAFETY INFORMATION

Warning:

Do not store explosive substances such as aerosol cans with a 

flammable propellant in this appliance.

Warning:

Do not use electrical appliances inside the storage compartments of this 

appliance.

Warning:

Keep ventilation openings of the appliance enclosure or the structure of 

built in equipment, clear of obstruction.

Warning:

Do not use mechanical devices or other means to accelerate the 

defrosting process.

Warning:

Do not damage the refrigerant circuit, i.e. pipe work or components.

 

ELECTRICAL

 

The appliance must be disconnected from its power source during 

cleaning; when maintenance and the replacement of parts is required, 

the equipment must be safely disconnected and isolated from the 

power supply using a lock-off system at the isolation device.

It is advised that the electrical supply to the equipment is protected by 

an appropraietly selected Residual Current Device (RCD) with a rating no 

greater than 30mA.

 

If the supply cord is damaged, it must be replaced by a service engineer 

or other qualified person.  Only the supply cord supplied by Williams 

Refrigeration must be used.
Fixed wiring appliances (those not supplied with a plug) shall incorporate 

a switch disconnector to meet the specification of IEC 60947; this is to 

be installed within the fixed wiring installation in accordance to the local 

wiring rules / regulation to provide all pole disconnection of the power    

            supply.

IMPORTANT SAFETY INFORMATION

Содержание Medi+ LWMP620

















Отзывы: