Whirlpool WET4027HW0, Руководство по обслуживанию

Страница: 8 / 82

1-4
n
27” Stacked Laundry Center
GENERAL INFORMATION
Control Panel and Features
Washer
1. WASH CYCLE KNOB
Use the Wash Cycle knob to select available cycles on your
washer. Turn the knob to select a cycle for your laundry
load.
See “Washer Cycle Guide” for detailed descriptions of
cycles.
2. WASH TEMP
You may select a Wash Temperature based on the type
of fabric and soils being washed. Use the warmest
wash water safe for the fabric. Follow garment label
instructions.
3. FABRIC SOFTENER
Set this knob to Yes when adding fabric softener to the
fabric softener dispenser.
4. WASHER START/PAUSE
Press the START/PAUSE button to start the washer.
5. WASH STATUS INDICATOR LIGHTS
7
3
4
1
CONTROL PANEL AND FEATURES
2
WASH CYCLE KNOB
Use the Wash Cycle knob to select available cycles on your
washer. Turn the knob to select a cycle for your laundry load.
See “Washer Cycle Guide” for detailed descriptions of cycles.
WASH TEMP
You may select a Wash Temperature based on the type of
fabric and soils being washed. Use the warmest wash water
safe for the fabric. Follow garment label instructions.
FABRIC SOFTENER
Set this knob to Yes when adding fabric softener to the
fabric softener dispenser.
START/PAUSE
Press the START/PAUSE button to start the washer.
WASH STATUS INDICATOR LIGHTS
The Cycle Status lights show the progress of a cycle.
At each stage of the process, you may notice sounds
or pauses that are different from your previous washer.
SENSE FILL
When the Start/Pause button is pressed, the washer will fill
and begin sensing to determine load size and balance.
Once sensing is complete, the washer will fill to the
appropriate level for the detected load size and then begin
the wash phase of the cycle.
NOTE: Sensing and wash phases will be paused by opening
the unlocked lid. Close the lid to resume the cycle. If the lid
is left open for more than 10 minutes, the washer will cancel
the cycle and pump out the water. The lid will lock after the
wash phase to begin the initial spinout and remain locked
for the remainder of the cycle.
1
2
3
4
5
Not all features and options are available on all models. Appearance may vary.
6
WASHER
WASH
The washer will fill to the correct water level based on the load
size. Certain cycles may agitate during the fill process to boost
cleaning. You will hear the agitator rotate, followed by a pause
lasting several seconds. When the wash cycle begins, you will
hear the agitator increase speed. The motor sounds may change
at different stages in the wash cycle while the washer performs
different wash actions.
RINSE
Certain cycles use a spray rinse, which adds water to the tub
while the basket spins. You may hear the motor turning on briefly
(short hum) to move the basket while filling.
DRAIN/SPIN
The washer spins the load at increasing speeds for proper water
removal, based on the selected cycle.
DONE
Once the cycle is complete, this light will come on. Remove the
load promptly for best results.
LID LOCK
The Lid Lock feature allows for
higher spin speeds. When the Lid
Lock light is lit, the lid is locked and
cannot be opened without pausing
the cycle. When the light is off, the
lid can be opened.
To open the lid after it has been
locked, press START/PAUSE.
The lid will unlock once the
washer movement has stopped.
This may take several minutes if
the load was spinning at high speed.
Press START/PAUSE again to resume the cycle.
5
7
3
4
1 2
6
5 7
STANDARD VENT MODELS
LONG VENT MODELS
The Cycle Status lights show the progress of a cycle. At
each stage of the process, you may notice sounds or
pauses that are different from your previous washer.
7
3
4
1
CONTROL PANEL AND FEATURES
2
WASH CYCLE KNOB
Use the Wash Cycle knob to select available cycles on your
washer. Turn the knob to select a cycle for your laundry load.
See “Washer Cycle Guide” for detailed descriptions of cycles.
WASH TEMP
You may select a Wash Temperature based on the type of
fabric and soils being washed. Use the warmest wash water
safe for the fabric. Follow garment label instructions.
FABRIC SOFTENER
Set this knob to Yes when adding fabric softener to the
fabric softener dispenser.
START/PAUSE
Press the START/PAUSE button to start the washer.
WASH STATUS INDICATOR LIGHTS
The Cycle Status lights show the progress of a cycle.
At each stage of the process, you may notice sounds
or pauses that are different from your previous washer.
SENSE FILL
When the Start/Pause button is pressed, the washer will fill
and begin sensing to determine load size and balance.
Once sensing is complete, the washer will fill to the
appropriate level for the detected load size and then begin
the wash phase of the cycle.
NOTE: Sensing and wash phases will be paused by opening
the unlocked lid. Close the lid to resume the cycle. If the lid
is left open for more than 10 minutes, the washer will cancel
the cycle and pump out the water. The lid will lock after the
wash phase to begin the initial spinout and remain locked
for the remainder of the cycle.
1
2
3
4
5
Not all features and options are available on all models. Appearance may vary.
6
WASHER
WASH
The washer will fill to the correct water level based on the load
size. Certain cycles may agitate during the fill process to boost
cleaning. You will hear the agitator rotate, followed by a pause
lasting several seconds. When the wash cycle begins, you will
hear the agitator increase speed. The motor sounds may change
at different stages in the wash cycle while the washer performs
different wash actions.
RINSE
Certain cycles use a spray rinse, which adds water to the tub
while the basket spins. You may hear the motor turning on briefly
(short hum) to move the basket while filling.
DRAIN/SPIN
The washer spins the load at increasing speeds for proper water
removal, based on the selected cycle.
DONE
Once the cycle is complete, this light will come on. Remove the
load promptly for best results.
LID LOCK
The Lid Lock feature allows for
higher spin speeds. When the Lid
Lock light is lit, the lid is locked and
cannot be opened without pausing
the cycle. When the light is off, the
lid can be opened.
To open the lid after it has been
locked, press START/PAUSE.
The lid will unlock once the
washer movement has stopped.
This may take several minutes if
the load was spinning at high speed.
Press START/PAUSE again to resume the cycle.
5
7
3
4
1 2 6
5
7
STANDARD VENT MODELS
LONG VENT MODELS
SENSE/FILL
When the Start/Pause button is pressed, the washer
will fill and begin sensing to determine load size and
balance. Once sensing is complete, the washer will fill to
the appropriate level for the detected load size and then
begin the wash phase of the cycle.
NOTE: Sensing and wash phases will be paused by
opening the unlocked lid. Close the lid to resume the
cycle. If the lid is left open for more than 10 minutes, the
washer will cancel the cycle and pump out the water.
The lid will lock after the wash phase to begin the initial
spinout and remain locked for the remainder of the cycle.
WASH
The washer will fill to the correct water level based on
the load size. Certain cycles may agitate during the fill
process to boost cleaning. You will hear the agitator
rotate, followed by a pause lasting several seconds. When
the wash cycle begins, you will hear the agitator increase
speed. The motor sounds may change at different stages
in the wash cycle while the washer performs different
wash actions.
RINSE
Certain cycles use a spray rinse, which adds water to
the tub while the basket spins. You may hear the motor
turning on briefly (short hum) to move the basket while
filling.
DRAIN/SPIN
The washer spins the load at increasing speeds for proper
water removal, based on the selected cycle.
Not all features and options are available on all models. Appearance may vary.