Westinghouse PT10110, Инструкция по эксплуатации, Страница: 10 / 18

10 8
To lock the trigger switch in the ON
position, pull back on the trigger switch
(2) to start the drill and push the trigger
switch lock button (3) into the drill
handle. Release the trigger switch while
holding the trigger switch lock button
into the drill handle. The drill will
continue to run. To release the trigger
switch lock button, pull trigger switch
back and then release the trigger.
DRILL / IMPACT SWITCH
The drill / impact switch (1) changes the
drilling mode between conventional
drilling and impact for drilling concrete
(see Fig. 2). To operate the drill in drill
mode, push the drill / impact switch to
the left. To operate the drill in impact
mode, push the drill / impact switch to
the right.
WARNINGS:
a) Always use face shield, hearing
protection and a dust mask when
drilling in concrete.
b) Always use carbide tipped masonry
bits when drilling in masonry. Any
other type of bit could break and
possibly cause serious injury.
FORWARD / REVERSE SWITCH
The forward / reverse switch (1) is
conveniently mounted above the trigger
switch (2) (see Fig. 1). To make the drill
rotate clockwise for drilling or driving
screws, push the forward / reverse
switch to the right. To make the drill
rotate counter clockwise for removing
screws, push the forward / reverse
switch to the left.
NOTES:
a) Never change position of the forward
/ reverse switch while chuck is turning.
b) The trigger switch will NOT function
with the forward / reverse switch in the
middle position.
VARIABLE SPEED TRIGGER SWITCH
This drill is equipped with a variable
speed ON / OFF trigger switch.
1. To start drill, gently squeeze the
trigger switch (2) (see Fig. 1).
NOTE: Drill will turn at its slowest speed
when the trigger switch is moved only a
small amount. The drill will turn at its
fastest speed when the trigger switch is
fully depressed.
2. To stop the drill, release the trigger
switch.
NOTE: Drilling at a slow drilling speed
for an extended period of time may
cause the drill motor to overheat. If the
drill gets hot, stop drilling and allow it
to cool for at least 15 minutes.
TRIGGER SWITCH LOCK
The trigger switch lock-on feature
allows the trigger switch to be locked in
the ON position at full speed when
continuous operation for extended
periods of time is required (see Fig. 1).
ASSEMBLY & OPERATION
Fig. 1
Fig. 2
ACCESORIOS DISPONIBLES
ADVERTENCIA: Utilice solamente
los accesorios recomendados para este
taladro de impacto. Siga las
indicaciones que vienen con los
accesorios. El uso de los accesorios
inapropiados podría causarle daños al
operador o también al mismo taladro
de impacto.
No utilice un accesorio sin antes haber
leído detalladamente las indicaciones o
el manual del propietario sobre ese
accesorio.
• Brocas del taladro
• Ruedas para sacar brillo
• Tambores para limar
• Serrucho de agujeros
• Accesorios para esparcir pintura
CONTENIDO DE LA CAJA
ADVERTENCIA: Si alguna pieza
falta o se encuentra dañada, no
enchufe el taladro de impacto dentro
de la fuente de alimentación hasta que
la pieza extraviada sea reemplazada.
Desempaque cuidadosamente el
taladro. Compare las piezas con la tabla
de "Piezas del taladro" a la derecha.
NOTE: Vea la página 9 para la ilustra-
ción de las piezas
ADVERTENCIA: Para prevenir
incendios o alguna reacción tóxica, no
utilice gasolina, nafta, acetona,
disolvente de laca o algún solvente
alta-mente volátil para limpiar el
taladro.
ACCESORIOS Y CONTENIDO DE LA CAJA
CONTENIDO DE LA CAJA – cont.
PIEZAS DEL TALADRO
KEY
A
B
C
D
QTY
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
DESCRIPCION
Taladro
Llave del portabrocas
Varilla de profundidad
Mango auxiliar
Piezas de mampostería
•1/8"(3,1mm)
•3/16"(4,7mm)
•1/4"(6,3mm)
•5/16"(7,9mm)
•3/8"(9,5mm)
•7/16"(11,1mm)
• 1/2"(12,7mm)
•9/16"(14,2mm)
•5/8"(15,8mm)
• 3/4"(19mm)
Manual del propietario
E