background image

 

-- 2 -- 

III. Working Principle 

All fresh air with moisture goes through air filter and enters the     

evaporator. As the temperature of evaporator surface is lower than dew point temperature of moisture, the moisture will 

be condensed into water drops and be collected to water tray, and then flows to bottom tank. The collected water is 

treated with activated carbon filters, reverse osmosis (RO) and sterilization by Ultraviolet device to be processed into 

drinking water or for other uses.   

The output water quality meets the standard GB5749-2006 of P.R.C. 

. Machine Receipt, Installation and Adjustment 

1. Machine Receiving 

Please check the machine and spare parts according to packing list. 

2. Installation 

2.1 Crane and forklift should be used for the transport and installation. Handle with care. When crane is rigged to    the 

machine,    ropes must be of same length and the hanging angle must be more than 45 degrees to avoid damage or 

scratching to the machine. The hanging ropes must be strong enough for the operation. 

  

2.2 The machine must be placed on level ground and be a certain distance from buildings; 1 meter at least between 

air  inlet  of  condenser  and  the  building,  1.5  meter  for  air  exhaust.  Place  the  machine  in  a  place  without  direct 

sunlight and away from heat source preferably covered from rain and sunshine. There should not be barrier effecting 

ventilation around the air inlet and outlet of the machine. Do not run the machine in circumstances of    alot of dust 

or serious chemical pollution.       

2.3 The machine should be equipped with independent power supply system and power distribution cabinet. The user 

should also provide a master air switch. When there is a big fluctuation in electrical voltage, the machine must be 

equipped  with  independent  voltage  regulator.  The  power  supply  adopts  3-phase  4-wire  system  phase.  Voltage 

deviation should not be exceeding 10% of the rated value. The maximum allowed unbalance in phase voltage is 2%. 

The machine must have a reliable earthing to ensure personal safety.

 

 

 
 

2.4 Check the machine and see if there is any partial damage or deformed parts during the transport. Check all wirings if 

there is any loosening.

 

2.5 Connect power cables as per Picture 2.5.1 (Use cable with designated size or thicker size) 

 

 

2.5.1 

3. System Adjustment 

After  the  machine’s  arrival,  positioning  and  installation  is  completed,  please  check  up  the  following  before 

connection to electricity.   

3.1 

Checkup before switching on the machine

.

 

!

    Notice

Phase voltage unbalance exceeds 2%. Do not turn on. 

Содержание WES-250





















Отзывы: