WES WES-250 Скачать руководство пользователя

Страница: 1 / 20

World Environmental Solutions Pty Ltd.

Manual for a WES 250L and WES 500L

Ⅰ. Summary --------------------------------------------------------------------------------------1

Ⅱ. Technical Specifications -------------------------------------------------------------------1

Ⅲ. Working Principle -------------------------------------------------------------------------2

Ⅳ. Machine Acceptance, Installation and Adjustment -----------------------------------2

Ⅴ. Operation----------------------------------------------------------------------------------------3

Ⅵ. Precautions

------------------------------------------------------------------------------------------------9

Ⅶ. Maintenance

-----------------------------------------------------------------------------------------------10

Ⅷ. Troubleshooting

-------------------------------------------------------------------------------------------------11

ANNEX I -------------------------------------------------------------------------------13

ANNEX II ------------------------------------------------------------------------------18

ANNEX

Ⅲ

-----------------------------------------------------------------------------19

Notice

：

This machine does not install RO film in it by default. Please install RO film inside the

machine before starting. (Please follow page 14 CLEAN AND REPLACE RO FILTERS to install)

The pictures in this instruction manual are only for reference purposes only.
NOTE: There may be technical changes or changes in structural design without prior notification

Содержание WES-250





















Результаты поиска

Содержание WES-250

Отзывы:

Похожие инструкции для WES-250

Бренды по названию

Популярные бренды

WES WES-250, Руководство пользователя

Результаты поиска

Содержание WES-250

Отзывы:

Похожие инструкции для WES-250

Бренды по названию

Популярные бренды