Weldtronic TM250C Скачать руководство пользователя страница 41

Страница: 41 / 48

TitanMig AU 250C Manual_ Issue A 0415

4.3 GTAW (TIG) Welding Trouble Shooting

The following chart addresses some common problems during TIG Welding.
In the event of equipment malfunction, contact an authorized service agent

Possible Reason

Suggested Solution

Tungsten burning Quickly

Incorrect Gas or No Gas

Check Pure Argon is in use

Insufficient Gas Flow

Check gas flow. Set to 10-15 l/min

Back Cap not fitted correctly

Check Back cap is fitted correctly and o ring in tact

Torch connected to (+) connection

Refit torch to (-) connection

Wrong Tungsten

Check Colour of tungsten & change to correct type

Tungsten oxidizing after weld

Post gas insufficient. Gas flow suggested 10-15 S after end of weld cycle

Contaminated Tungsten

Touching Tungsten into Weld Pool

Keep tungsten raised to 2-5mm of workpeice

Touching Filler wire to Tungsten

Feed filler into the leading edge of the weld pool

Tungsten Melting

Check Type & Size Tungsten being used

Porosity

Incorrect Gas or No Gas

Check Pure Argon is in use

Insufficient Gas Flow

Check gas flow. Set to 10-15 l/min

Contaminated base metal

Remove any paint , grease, oil & dirt

Contaminated TIG Wire

Use clear dry rust free wire only.

Unstable Arc

Torch connected to (+) connection

Refit torch to (-) connection

Contaminated base metal

Remove any paint , grease, oil & dirt

Contaminated Tungsten

Cut & re-grind Tungsten

Arc length too long

Keep torch raised to 2-5mm of workpeice

Wandering Arc

Incorrect Gas or No Gas

Check Pure Argon is in use

Wrong Tungsten

Check Colour of tungsten & change to correct type

Poorly prepared Tungsten

Ensure Tungsten is ground lengthways

Contaminated base metal

Remove any paint , grease, oil & dirt

Contaminated TIG Wire

Use clear dry rust free wire only.

Difficulty Starting Arc

Incorrect Gas or No Gas

Check Pure Argon is in use

Contaminated Tungsten

Cut & re-grind Tungsten

Wrong Tungsten

Check Colour of tungsten & change to correct type

Loose connection

Check connections

Earth Clamp not connected

Connect earth clamp to the work piece

Содержание TM250C

















































Результаты поиска

Содержание TM250C

Отзывы:

Похожие инструкции для TM250C

Бренды по названию

Популярные бренды

Weldtronic TM250C, Руководство по эксплуатации

Результаты поиска

Содержание TM250C

Отзывы:

Похожие инструкции для TM250C

Бренды по названию

Популярные бренды