background image

 

Wiring Requirements 

 

WARNING 

Safety First!

 

Turn the power off before disconnecting modules or wires. 
The correct power supply voltage is listed on the product 
label. Check the voltage of your power source to make sure 
that you are using the correct voltage. Do 

NOT

 use a 

voltage greater than what is specified on the product label. 

 

WARNING 

Safety First!

 

Calculate the maximum possible current in each power wire 
and common wire. Observe all electrical codes dictating the 
maximum current allowable for each wire size. 

If the current goes above the maximum ratings, the wiring 
could overheat, causing serious damage to your equipment. 

 

You should also pay attention to the following points: 

  Use separate paths to route wiring for power and devices. If power 

wiring and device wiring paths must cross, make sure the wires are 
perpendicular at the intersection point. 
NOTE: Do not run signal or communications wiring and power wiring 
in the same wire conduit. To avoid interference, wires with different 
signal characteristics should be routed separately. 

  You can use the type of signal transmitted through a wire to 

determine which wires should be kept separate. The rule of thumb is 
that wiring that shares similar electrical characteristics can be 
bundled together. 

  Keep input wiring and output wiring separated. 

  It is strongly advised that you label wiring to all devices in the system 

when necessary. 

 

Grounding the Ethernet Switch 

Grounding and wire routing help limit the effects of noise due to 
electromagnetic interference (EMI). Run the ground connection from the 
ground screw to the grounding surface prior to connecting devices. 

 

ATTENTION 

This product is intended to be mounted to a well-grounded 
mounting surface such as a metal panel. 

 
 
 
 
 
 
 

Содержание IE-SW-BL06-1TX-4PoE-1SC

















Отзывы: