background image

11 

 

100BaseFX Ethernet Port Connection 

The concept behind the SC/ST port and cable is quite straightforward. 
Suppose you are connecting devices I and II; contrary to electrical 
signals, optical signals do not require a circuit in order to transmit data. 
Consequently, one of the optical lines is used to transmit data from 
device I to device II, and the other optical line is used transmit data from 
device II to device I, for full-duplex transmission. 

Remember to connect the 

Tx (transmit)

 port of device I to the 

Rx 

(receive)

 port of device II, and the 

Rx (receive)

 port of device I to the 

Tx (transmit)

 port of device II.  

SC-Port Pinouts

 

ST-Port Pinouts

 

 

 

 

 

ATTENTION 

This is a Class 1 Laser/LED product. To avoid causing 
serious damage to your eyes, do not stare directly into the 
Laser Beam. 

 

Redundant Power Inputs 

Both power inputs can be connected simultaneously to live DC power 
sources. If one power source fails, the other live source acts as a 
backup, and automatically supplies all of the Ethernet Switch power 
needs. 

 

DIP Switch Settings 

 

The default setting for each DIP Switch is 
OFF. The following table explains the effect 
of setting the DIP Switches to the ON 
positions. 

 

DIP Switch 

Setting 

Description 

- - - - 

 

Serves no function (reserved for future use). 

BSP 

ON 

Enables broadcast storm protection 

OFF 

Disables broadcast storm protection 

Содержание IE-SW-BL06-1TX-4PoE-1SC

















Отзывы: