background image

 

Wiring the Redundant Power Inputs 

The top two contacts and the bottom two contacts of the 4-contact 
terminal block connector on the top panel are used for the Ethernet 
Switch´s two DC inputs. Top and front views of one of the terminal block 
connectors are shown here. 

 

STEP 1

: Insert the negative/positive DC wires into the V-

/V+ terminals. 

 

STEP 2

: To keep the DC wires from pulling loose, use a 

small flat-blade screwdriver to tighten the wire-clamp 
screws on the front of the terminal block connector. 

 

STEP 3

: Insert the plastic terminal block connector prongs 

into the terminal block receptor, which is located on 
Ethernet Switch top panel. 

 

 

 

ATTENTION 

Before connecting the Ethernet Switch to the DC power 
inputs, make sure the DC power source voltage is stable. 

 

 

Communication Connections 

The IE-SW-BL06 series has 4, 5 or 6 10/100BaseT(X) Ethernet ports 
and 2, 1 or 0 (zero) 100BaseFX multi-mode (SC/ST-type connector) 
fiber ports. 4 of the 10/100BaseT(X) ports are PoE capable according to 
IEEE 802.3 af/at.  

 

10/100BaseT(X) Ethernet Port Connection 

10/100BaseT(X) ports located on the Ethernet Switch front panel are 
used to connect to Ethernet-enabled devices. Below we show pinouts 
for both MDI (NIC-type) ports and MDI-X (HUB/Switch-type) ports, and 
also show cable wiring diagrams for straight-through and cross-over 
Ethernet cables. 

MDI Port Pinouts 

MDI-X Port Pinouts 

8-pin RJ45 

Pin 

Signal 

Pin 

Signal 

 

Tx+ 

Rx+ 

Tx- 

Rx- 

Rx+ 

Tx+ 

Rx- 

Tx- 

 
 
 
 
 
 

Содержание IE-SW-BL06-1TX-4PoE-1SC

















Отзывы: