WEICHAI WP6GTA Скачать руководство пользователя

Страница: 51 / 90

Weichai America Corp.

Intake and Exhaust System

5.1

Intake and Exhaust System Assembly and Disassembly

5.1.1 Intake and Exhaust System Exploded View

Fig. 5-1 Exploded view of intake and exhaust system

5.1.2 Intake and Exhaust System Disassembly Procedure

Loosen the clamps on the air filter elbow, elbow pipe breather connection, and the mixer

hose. Remove the air filter elbow, elbow pipe, and mixer hose.

Remove the hex bolts bolting the air filter to the air filter bracket. Remove the air filter

Remove the socket head bolts bolting the throttle adapter to the mixer. Remove the mixer.

Note: If the EPR has not been removed, remove the hex bolts bolting the EPR to the mixer.

Remove the nut and bolt bolting the intake elbow to the throttle and throttle adapter. Remove

the throttle adapter and throttle together in one piece, then the throttle gasket.

Note: After removal, hold the throttle and throttle adapter together with bolt holes still aligned

exhaust pipe group

intake pipe group

turbocharger group

Содержание WP6GTA



























































































Результаты поиска

Содержание WP6GTA

Отзывы:

Похожие инструкции для WP6GTA

Бренды по названию

Популярные бренды

WEICHAI WP6GTA, Руководство по сборке/разборке

Результаты поиска

Содержание WP6GTA

Отзывы:

Похожие инструкции для WP6GTA

Бренды по названию

Популярные бренды