WEICHAI WP6GTA страница 56 Скачать руководство пользователя

Страница: 56 / 90

Weichai America Corp.

5.4.2 Disassembling steps of turbocharger system

Disassemble the turbocharger system with the reverse order of assembly.

5.4.3 Assembling steps for turbocharger system

Install the turbocharger gasket to the exhaust manifold flange.

Install the gasket on the exhaust manifold flange to install the turbocharger assembly, and

loosely install the style 2 all-metal hexagon lock nuts and tighten them.

Apply a proper amount of clean lubricating oil to the turbocharger intake port, and wipe the

excessive lubricating oil.

Install the gasket, studs and connect the muffler.

All the gaskets can only be used for once and shall be replaced when repairing.

5.4.4 Inspection and maintenance of turbocharger system

1. Check the running of rotor

Turn the air compressor stator with hand; if it rotates for more than one turn, it indicates that it is

normal; if it stops rotating soon, it indicates that the bearing is worn abnormally or there is

interference between the moving part and the fixed part or the moving part is blocked; in this

case, you shall find out the causes and eliminate them.

2. Check the axial play of rotor

Place the measuring head of the dial indicator against the air compressor end, push and pull the

rotating shaft with hand in the axial direction, and measure and record the difference value as

shown in the figure 5-5.

The rotor axial play shall be in the range of (0.088~0.118) mm; if it goes out of this range, it

indicates that the thrust bearing plate or the thrust plate and bearing body are worn; in this case,

you shall find out the causes and eliminate them.

Содержание WP6GTA



























































































Результаты поиска

Содержание WP6GTA

Отзывы:

Похожие инструкции для WP6GTA

Бренды по названию

Популярные бренды

WEICHAI WP6GTA, Руководство по сборке/разборке

Результаты поиска

Содержание WP6GTA

Отзывы:

Похожие инструкции для WP6GTA

Бренды по названию

Популярные бренды