WEICHAI WP6GTA Скачать руководство пользователя страница 89

Страница: 89 / 90

Weichai America Corp.

d) Unstable charging voltage

Failure4: Unstable charging voltage

Vehicle fault

Fault testing

Troubleshooting

When engine
runs normally,
voltmeter
indicates
charging, with
its needle
wobbling, and
it is impossible
to identify its
reading (or
charging
indicator comes
on and goes out
repeatedly).

a. Alternator and related belt is loose, belt
slippage.

Tension alternator and related belt.

b. The joints of charging circuit get loose
causing bad connection

Inspect all connections of charging circuit.

c. Dirt accumulation at slip ring,
excessive wear of electric brush, or brush
spring is weak or broken

Remove dirt, or replace electric brush and its spring.

d. Regulator damaged.

Replace the regulator.

Abnormal noise from alternator

Failure 5: Abnormal noise from alternator

Vehicle fault

Fault testing

Troubleshooting

Alternator
sounds
abnormally
during

its

running.

a. Deformed alternator mounting bracket
or getting too close with external engine
body

Improve the mounting bracket strength and adjust
mounting condition.

b. Alternator belt is loose causing
slipping

Replace the alternator belt.

c. Loose alternator pulley

Tighten pulley

d. Alternator bearing oil shortage or
damaged

Replace the alternator bearing

e. Muffled noise from the inside of
alternator

Stator coil is short circuited, and should be replaced.

f. Whistle noise from alternator changing
with speed.

It is a noise produced by vibration of stator core
vibration, and replace stator assembly if necessary.

Содержание WP6GTA



























































































Результаты поиска

Содержание WP6GTA

Отзывы:

Бренды по названию

Популярные бренды

WEICHAI WP6GTA, Руководство по сборке/разборке

Результаты поиска

Содержание WP6GTA

Отзывы:

Бренды по названию

Популярные бренды