WEICHAI WP6GTA Скачать руководство пользователя

Страница: 85 / 90

Weichai America Corp.

When providing warranty service for user, check the alternator on vehicle for malfunction. Tool:

test lamp, the process is as shown in figure 11-3.

Figure 11-3 Diagnosis Trouble Flow Chart for Alternator

2. Failure diagnosis & troubleshooting method of charging system

a) It is not charging

Failure 1: It is not charging

Turn on the power switch of the vehicle, and connect the test

lamp to the terminal B+ and E (negative pole) of the

alternator

Is the test lamp ON?

Connect the wire from terminal E to

terminal D+ of the alternator

Is the test lamp light

ON?

Start the engine

Is the test lamp light

ON?

The alternator is

trouble free

Alternator malfunction

It indicates that the internal electric circuit of wiring

terminal D+ of the alternator is malfunctioning

It indicates that there is no voltage at wiring

terminal B+ of alternator and the wire to the positive

pole of battery is malfunctioning

Yes

Содержание WP6GTA



























































































Результаты поиска

Содержание WP6GTA

Отзывы:

Похожие инструкции для WP6GTA

Бренды по названию

Популярные бренды

WEICHAI WP6GTA, Руководство по сборке/разборке

Результаты поиска

Содержание WP6GTA

Отзывы:

Похожие инструкции для WP6GTA

Бренды по названию

Популярные бренды