NOVAK BALLISTIC Instructions Download

Page: 1 / 2

PRECAUTIONS

NEVER FREE-REV THE MOTOR

Free-running your brushless

motor in a no-load condition can result in rotor failure and ESC

transistor damage & will void the product’s warranty!

• WATER & ELECTRONICS DON’T MIX

Never allow water, moisture, or

other foreign materials to get inside motor, or on PCBs.

• NOVAK MOTORS & ESCs FOR BEST RESULTS

Use Novak sensored

motors with Novak Brushless ESCs for best performance & protection. Only

use motors with the proper number of turns to match ESC’s rating.

Use of this brushless motor with non-Novak ESCs and ESCs that

advance motor timing can result in excessive current draw & severe

motor damage that will NOT be covered by the product’s warranty!

•

DO NOT use Ballistic 550-Size 4.5T-5.5T motors above a 3S Li-Po pack.

• INSULATE EXPOSED WIRES

Use heat shrink tubing to prevent shorts.

• NO SOLVENTS

Do NOT expose the motor to any type of solvents.

• SET GEAR MESH PROPERLY

Too tight of a gear mesh can result in

motor pinion shaft breakage--be sure to adjust mesh properly.

NEVER FREE-REV THE MOTOR

Free-running your brushless

motor in a no-load condition can result in rotor failure and ESC

transistor damage & will void the product’s warranty!

• WATER & ELECTRONICS DON’T MIX

Never allow water, moisture, or

other foreign materials to get inside motor, or on PCBs.

• NOVAK MOTORS & ESCs FOR BEST RESULTS

Use Novak sensored

motors with Novak Brushless ESCs for best performance & protection. Only

use motors with the proper number of turns to match ESC’s rating.

Use of this brushless motor with non-Novak ESCs and ESCs that

advance motor timing can result in excessive current draw & severe

motor damage that will NOT be covered by the product’s warranty!

•

DO NOT use Ballistic 550-Size 4.5T-5.5T motors above a 3S Li-Po pack.

• INSULATE EXPOSED WIRES

Use heat shrink tubing to prevent shorts.

• NO SOLVENTS

Do NOT expose the motor to any type of solvents.

• SET GEAR MESH PROPERLY

Too tight of a gear mesh can result in

motor pinion shaft breakage--be sure to adjust mesh properly.

MOTOR MAINTENANCE

• CHECK ALL MOTOR SCREWS

for loosening at regular intervals, just like

other hardware on your vehicle.

Note: The 3 main socket head screws

that hold the motor together may require tightening after a few runs of

the motor.

Also check the 3 flat head screws securing the end cap on

the back of the motor.

• CHECK MOTOR BEARING WEAR

after extensive use. The motor’s

closed design will keep most dirt & debris out, but some will get in

and eventually cause wear. If the shaft does not spin freely, you may

need bearing replacement

(replacement bearing accessory kits are available

from Novak)

. A small drop of light oil on the bearings periodically can

help extend bearing life

--however, too much oil will attract dirt and will

cause problems, so apply sparingly

• CLEAN INSIDE MOTOR

periodically by removing front end bell,

removing the rotor, and blowing out the inside of the motor with

compressed air.

Be sure not to lose any small shim washers that may be

on the ends of the rotor shaft & keep them in the correct location.

• CHECK ALL MOTOR SCREWS

for loosening at regular intervals, just like

other hardware on your vehicle.

Note: The 3 main socket head screws

that hold the motor together may require tightening after a few runs of

the motor.

Also check the 3 flat head screws securing the end cap on

the back of the motor.

• CHECK MOTOR BEARING WEAR

after extensive use. The motor’s

closed design will keep most dirt & debris out, but some will get in

and eventually cause wear. If the shaft does not spin freely, you may

need bearing replacement

(replacement bearing accessory kits are available

from Novak)

. A small drop of light oil on the bearings periodically can

help extend bearing life

--however, too much oil will attract dirt and will

cause problems, so apply sparingly

• CLEAN INSIDE MOTOR

periodically by removing front end bell,

removing the rotor, and blowing out the inside of the motor with

compressed air.

Be sure not to lose any small shim washers that may be

on the ends of the rotor shaft & keep them in the correct location.

SERVICE PROCEDURES

Consider changing out motor parts yourself. All of the Ballistic’s main components are

available as service items--Refer to ‘Accessories’ section or check out our website. In

most cases, replacing motor parts is less expensive than sending in your motor for service.

After reviewing instructions, tech section and how-to video section of website, if you feel

your motor requires service

(motor may appear to have failed when other problems exist)

, obtain

the most current product service options & pricing by one of the following methods:

WEBSITE: Print a copy of the product

SERVICE FORM

from the SERVICE section of the

Novak website. Fill out the needed information & return it with the Novak product.

PHONE/E-MAIL: Contact our customer service department by phone or e-mail, and

we will supply you with current service options.

WARRANTY SERVICE: You

MUST CLAIM WARRANTY

on product

SERVICE FORM

& include

a valid, itemized receipt with the purchase date on it, or an invoice from previous service

work.

If warranty provisions have been voided, there will be a service fee.

ADDITIONAL NOTES:

• Dealers/distributors are not authorized to replace products thought to be defective.

• If a hobby dealer returns your product for service, submit a completed product

SERVICE

FORM

to dealer & make sure it’s included with items.

PRODUCT WARRANTY

Novak Brushless motors are guaranteed to be free from defects in materials or workmanship for a period of 120 days

from the original date of purchase

(verified by dated, itemized sales receipt)

. Warranty does not cover incorrect instal-

lation, components worn by use, cross-connection of battery/motor power wires, overheating solder tabs, damage

resulting from thermal overload or operation above 175°F, use of excessive timing or overheating, splices or damage to

the sensor harness, damage from disassembling motor, tampering with internal electronics, allowing water, moisture,

or any other foreign material to enter motor or get onto the PC board, short-circuiting of motor by allowing exposed

wiring or solder tabs to cross-connect or ESC applying simultaneous power to more than one phase at a time from

switching to Brush Mode, free-revving motor, or any damage caused by a crash, flooding, or natural disaster. In no case

shall our liability exceed the product’s original cost. We reserve the right to modify warranty provisions without notice.

Because Novak R/C, Inc. has no control over the connection & use of motor or other related electronics, no liability may

be assumed nor will be accepted for damage resulting from the use of this product. Every motor is thoroughly tested and

cycled before leaving our facility and is, therefore, considered operational. This product is not a toy, and is not intended

for use by children under 14 years of age without the strict supervision of an adult. Use of this product in a uncontrolled

manner may result in physical damage or injuries. Take extra care when operating any remote control vehicle.

By the act

of connecting/operating speed control, the user accepts all resulting liability.

e-mail:

[email protected]

• (949) 916-6044 • Monday-Thursday

©Novak R/C, Inc. California, U.S.A. • 55-3600-1.J • 4/2014

No part of these instructions may be reproduced without the written permission of Novak R/C, Inc.