WDS 1710 Series, Техническое руководство

Страница: 58 / 62

05-3305A01, Rev. E I-1
INDEX
A
ACCESS DENIED error message 19
Accessories 5
Accessory Power pinout (Pin 18) 12
Active messaging (defined) 44
Alarms
alarm code definitions 34
major vs. minor 33
pinout (Pin 25) 12
using STAT command to display 31
AMASK command 21
Antenna
installation 6
RSSI command used to refine heading 14
system gain, defined 44
Yagi, illustrated 9
Antennas 9
Applications 2
Multiple Address Systems (MAS) 2
point-to-multipoint system 2
point-to-point system 3
ASENSE command 23
B
BAUD command 24
Baud rate
setting for RJ-11 DIAG port (DLINK command) 26, 38
Bit, defined 44
Bits-per-second. See BPS 44
BPS (bits-per-second), defined 44
BUFF command 24
Byte, defined 44
C
Cable, loss due to length of coaxial at 400 MHz 9
Cable, loss due to length of coaxial at 960 MHz 10
Carrier
Switched 3
Cautions
use attenuation between all units in test setup 38, 41
CKEY command 25
Codes, Model Number 4
Command Descriptions 21
COMMAND FAILED error message 19
Command summary, table 19
Commands
AMASK (set/display alarm triggers) 21
ASENSE (set alarm output state) 23
BAUD (set/display rate, encoding) 24
BUFF (set/display data handling mode) 24
CKEY (enable/disable continuous keying) 25
CTS (set/display CTS line response timer) 25
DATAKEY (enable/disable transmitter keying by radio) 25
descriptions 21
–
32
DEVICE (set/display radio behavior) 25
DKEY (deactivate transmitter after KEY command) 26
DLINK (enable/disable network-wide diagnostics) 26
DTYPE (set radio to root or node for diagnostics) 26
DUMP (display all programmed settings) 26
entering on Hand-Held Terminal (HHT) 17
Hand-Held Terminal (HHT) 17
HREV (display hardware revision level) 27
INIT (reinitialize radio to factory defaults) 27
INIT xx10 (restore standard transceiver defaults) 27
INIT xx20 (configure radio for use with P-20 chassis) 27
KEY (activate transmitter) 28
Keyboard 17
MODEL (display radio model number code) 28
MODEM (set modem speed) 28
OWM (set/display owner
’
s message) 28
OWN (set/display owner
’
s name) 28
PTT (set/display key-up delay) 28
PWR (set/display RF forward output power) 28
RSSI (display RSSI) 29
RTU (enable/disable internal RTU) 29
RX (set/display receive frequency) 29
RXTOT (set/display receive time-out timer value) 30, 32
SCD (set/display soft-carrier dekey delay) 30
SER (display radio serial number 30
SHOW (display DC voltage, data port, RF power) 30
SNR (display signal-to-noise ratio) 30
SREV (display software revision level) 31
STAT (display current alarm status) 31
TEMP (display internal temperature) 31
TOT (set/display time-out value and timer status) 31
TX (set/display transmit frequency) 31
Conversions, dBm-Watts-Volts 43
CTS command 25
CTS pinout (Pin 5) 11
D
Data Circuit-terminating Equipment
—
See DCE 44
Data Communications Equipment
—
See DCE. 44
Data interface
connector pinouts 11
display active connector port 30
installing connection 11
Data Terminal Equipment
—
See DTE 44
DATAKEY command 25
dB. See Decibel 44
dBi, defined 44
dBm, defined 44
DCD
LED 14
pinout (Pin 8) 11
DCE (Data Circuit-terminating Equipment), defined 44
Decibel (dB), defined 44
Description, product 1
DEVICE command 25
Diagnostic Channel Enable, pinout (Pin 23) 12
Diagnostics
interface specifications 36
network-wide, performing 37, 39, 41
PC software used for 40
using InSite software for network-wide 37, 39